EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Investigation on the Structural Integrity of Solid Propellant Grains with Different-Sized Void Defects

Jianru Wang, Kai Liu, Tuanwei Xu, Jinkang Du, Yuanzhe Liang, Wenjing Li, Peng Cao iD

Materials · 22.07.2026 · 19 (14) · 3151

DOI: 10.3390/ma19143151 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 22.07.2026. Verfasst von Jianru Wang und 6 weiteren Autor:innen. Beteiligte Einrichtung: Academy of Aerospace Solid Propulsion Technology, Xi'an 710025, China. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 41 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

During the service of solid rocket motors, propellant grains need to bear various loads such as curing cooling, gravity, and combustion internal pressure. The internal pore defects will seriously affect the structural integrity. In this paper, a three-dimensional finite element model of propellant–insulation layer–mold is established to study the structural responses of pore defects with different sizes (30–100 mm) under three typical working conditions: curing cooling, curing cooling coupled with gravity, and internal pressure loading. It is found that under the curing cooling condition, compared with the non-porous propellant grain structure, the structure with pores will raise the overall mechanical response of the propellant grain, and the maximum stress and strain are mainly concentrated in the front end of the core hole and the wing groove area. The pore size has a limited impact on the overall stress distribution, but will change the local stress concentration degree. Among them, the 80 mm pore reduces the stress in the wing groove area through stress field interference. Moreover, large-size pores will significantly weaken the structural bearing capacity and increase the contact pressure between the propellant and the core mold. Under the condition of curing cooling coupled with gravity, the stress and strain are mainly distributed at the edge of the pores, and the values increase with the increase of pore size. Under the action of internal pressure load, the stress and strain in the middle section of the propellant grain have no obvious change, but stress concentration occurs in the transition area between the core hole and the wing groove and at the end of the wing groove. The results of this study provide a reference for the integrity evaluation and structural optimization of propellant grains with pore defects.

Schlagwörter

Stichwörter der Autor:innen

engineering design parameterspropellant grain integritysolid propellantvoid defect

Autor:innen und Institutionen

  • Academy of Aerospace Solid Propulsion Technology, Xi'an 710025, China.
  • National Graduate College for Elite Engineers, Beihang University, Beijing 100191, China.
  • The Institute of Xi'an Aerospace Solid Propulsion Technology, Xi'an 710025, China.
  • National Key Laboratory of Solid Rocket Propulsion, Xi'an 710025, China.
  • College of Architecture and Civil Engineering, Beijing University of Technology, Beijing 100124, China.

ORCID-Profile: Peng Cao

Zitieren

APA

Wang, J., Liu, K., Xu, T., Du, J., Liang, Y., Li, W., & Cao, P. (2026). Investigation on the Structural Integrity of Solid Propellant Grains with Different-Sized Void Defects. Materials, 19(14), 3151. https://doi.org/10.3390/ma19143151

Vancouver

Wang J, Liu K, Xu T, Du J, Liang Y, Li W, et al. Investigation on the Structural Integrity of Solid Propellant Grains with Different-Sized Void Defects. Materials. 2026;19(14):3151. doi:10.3390/ma19143151

BibTeX
@article{Wang2026,
  author = {Wang, Jianru and Liu, Kai and Xu, Tuanwei and Du, Jinkang and Liang, Yuanzhe and Li, Wenjing and Cao, Peng},
  title = {Investigation on the Structural Integrity of Solid Propellant Grains with Different-Sized Void Defects},
  journal = {Materials},
  year = {2026},
  volume = {19},
  number = {14},
  pages = {3151},
  doi = {10.3390/ma19143151}
}
Kostenlos starten →