EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Study on Basalt Fiber-Reinforced Lunar Regolith Simulant Geopolymer: Experiment and Constitutive Model

Jianghuai Zhan, Lepeng Huang, Ziheng Ding, Fei Wang, Shuai Li, Xuanyi Xue iD, Jianmin Hua

Materials · 14.07.2026 · 19 (14) · 3037

DOI: 10.3390/ma19143037 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 14.07.2026. Verfasst von Jianghuai Zhan und 6 weiteren Autor:innen. Beteiligte Einrichtung: School of Civil Engineering, Chongqing University, Chongqing 400045, China. Die Arbeit nennt 27 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: the National Key R&D Program of China, National Natural Science Foundation of China, Chongqing University.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Lunar regolith simulant (LRS) geopolymers are promising construction materials for lunar in situ resource utilization, but their brittle behavior and limited crack resistance restrict their structural applications. This study investigated the effect of basalt fiber length on the mechanical properties, failure modes, stress–strain behavior, constitutive relationship, and microstructure of CQU-1 LRS geopolymers. Basalt fiber-reinforced LRS geopolymers were prepared under weak alkali activation and high-temperature curing at 80 °C. The basalt fiber content was fixed at 0.1%, and six fiber lengths of 0, 6, 9, 12, 15, and 18 mm were considered. Compressive and flexural tests were conducted after curing for 1 d and 7 d, and the normalized stress–strain curves were fitted using the Saenz L.P., Carreira D.J., and Zhenhai Guo models. The results showed that basalt fiber length significantly affected the mechanical performance of LRS geopolymers. An appropriate fiber length improved strength, stiffness, ductility, and post-peak load-bearing capacity, whereas excessively short or long fibers weakened the reinforcing effect. The 15 mm fiber group exhibited the best overall performance. After curing for 1 d, its compressive strength reached 2.23 MPa, 49.7% higher than that of the control group, and its elastic modulus increased approximately 2.5-fold. After curing for 7 d, its compressive strength reached 13.44 MPa, 32.0% higher than that of the control group. The Zhenhai Guo model provided the best fit for the stress–strain curves. SEM-EDS analysis showed that basalt fibers improved interfacial bonding and promoted gel enrichment near the fiber–matrix interface. Overall, 15 mm was recommended as the optimal basalt fiber length for CQU-1 LRS geopolymers under the conditions used in this study.

Schlagwörter

Stichwörter der Autor:innen

basalt fiber lengthcompressive strengthflexural strengthlunar regolith simulantmicrostructurestress–strain constitutive model

Autor:innen und Institutionen

  • School of Civil Engineering, Chongqing University, Chongqing 400045, China.
  • State Key Laboratory of Safety and Resilience of Civil Engineering in Mountain Area, Chongqing 400045, China.
  • Department of Civil Engineering, The University of Hong Kong, Pokfulam Road, Hong Kong, China.

ORCID-Profile: Xuanyi Xue

Förderung

  • the National Key R&D Program of China
  • National Natural Science Foundation of China
  • Chongqing University
  • the National Key R&D Program of China

Zitieren

APA

Zhan, J., Huang, L., Ding, Z., Wang, F., Li, S., Xue, X., & Hua, J. (2026). Study on Basalt Fiber-Reinforced Lunar Regolith Simulant Geopolymer: Experiment and Constitutive Model. Materials, 19(14), 3037. https://doi.org/10.3390/ma19143037

Vancouver

Zhan J, Huang L, Ding Z, Wang F, Li S, Xue X, et al. Study on Basalt Fiber-Reinforced Lunar Regolith Simulant Geopolymer: Experiment and Constitutive Model. Materials. 2026;19(14):3037. doi:10.3390/ma19143037

BibTeX
@article{Zhan2026,
  author = {Zhan, Jianghuai and Huang, Lepeng and Ding, Ziheng and Wang, Fei and Li, Shuai and Xue, Xuanyi and Hua, Jianmin},
  title = {Study on Basalt Fiber-Reinforced Lunar Regolith Simulant Geopolymer: Experiment and Constitutive Model},
  journal = {Materials},
  year = {2026},
  volume = {19},
  number = {14},
  pages = {3037},
  doi = {10.3390/ma19143037}
}
Kostenlos starten →