Effect of Sintering Temperature on Densification, Microstructure, and Corrosion Behavior of Ti6Al4V/20Cu Composites Fabricated by Powder Metallurgy
Materials · 10.07.2026 · 19 (14) · 2979
DOI: 10.3390/ma19142979 ↗Kurz gefasst
Fachartikel in der Zeitschrift Materials, online erschienen am 10.07.2026. Verfasst von Victor Manuel Solorio und 8 weiteren Autor:innen. Beteiligte Einrichtung: División de Estudios de Posgrado e Investigación, Tecnológico Nacional de Mexico/I.T. Morelia, Av. Tecnológico #1500, Colonia Lomas de Santiaguito, M…. Die Arbeit nennt 26 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Department of Science, Humanities, Technology (SECIHTI), via postdoctoral fellowships of Elena Mihalcea.
Abstract (Originalsprache)
Copper alloying of Ti6Al4V via liquid-phase sintering (LPS) is a promising route to enhance densification and mechanical properties for biomedical implants. This study investigates the effect of sintering temperature (900–1100 °C) on the densification, microstructure, and electrochemical behavior of Ti6Al4V–20 wt.% Cu composites. Samples were fabricated via pressureless sintering, maintaining a constant relative green density of 72.7%. The results show that the relative density increased progressively from 78.6% at 900 °C to 98.1% at 1100 °C. Microstructural analysis revealed a transition from fragmented Ti-Cu dendritic structures to refined globular intermetallic, with enhanced copper diffusion into the α-Ti matrix above 1000 °C, accompanied by the formation of TiCu and Ti2Cu intermetallic phases. Correspondingly, microhardness increased systematically from 313 HV to 473 HV, correlated with reduced porosity and intermetallic reinforcement. Electrochemical tests in Ringer’s solution indicated that while higher temperatures improve structural integrity, the distribution of Cu-rich phases significantly influences corrosion kinetics. These findings demonstrate that sintering at 1100 °C optimizes the densification–microstructure relationship, providing a technical basis for the development of high-performance Ti-based composites. Based on previous studies of Ti–Cu systems, these materials may exhibit antibacterial activity, although no biological or antibacterial tests were performed in the present work.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- División de Estudios de Posgrado e Investigación, Tecnológico Nacional de Mexico/I.T. Morelia, Av. Tecnológico #1500, Colonia Lomas de Santiaguito, Morelia C.P. 58120, Mexico.
- Unidad Académica de Ingeniería I, Universidad Autónoma de Zacatecas, Zacatecas C.P. 98000, Mexico.
- Instituto de Investigaciones en Ciencias de la Tierra, Universidad Michoacana de San Nicolás de Hidalgo, Fco. J. Mujica S/N, Morelia C.P. 58060, Mexico.
- Departamento de Ingeniería Química Tecnológico Nacional de México/I.T.Celaya, Tecnológico Nacional de Mexico en Celaya, Celaya C.P. 38010, Mexico.
ORCID-Profile: Victor Manuel Solorio, Elena Mihalcea, Julio Villalobos-Brito, Francisco Alvarado-Hernandez, Jose Luis Cabezas-Villa, Gilberto González-Gómez, Luis Olmos
Förderung
- Department of Science, Humanities, Technology (SECIHTI), via postdoctoral fellowships of Elena Mihalcea
Zitieren
APA
Solorio, V. M., Vergara-Hernández, H. J., Mihalcea, E., Villalobos-Brito, J., Alvarado-Hernandez, F., Cabezas-Villa, J. L., González-Gómez, G., Machado-López, M. M., & Olmos, L. (2026). Effect of Sintering Temperature on Densification, Microstructure, and Corrosion Behavior of Ti6Al4V/20Cu Composites Fabricated by Powder Metallurgy. Materials, 19(14), 2979. https://doi.org/10.3390/ma19142979
Vancouver
Solorio VM, Vergara-Hernández HJ, Mihalcea E, Villalobos-Brito J, Alvarado-Hernandez F, Cabezas-Villa JL, et al. Effect of Sintering Temperature on Densification, Microstructure, and Corrosion Behavior of Ti6Al4V/20Cu Composites Fabricated by Powder Metallurgy. Materials. 2026;19(14):2979. doi:10.3390/ma19142979
BibTeX
@article{Solorio2026,
author = {Solorio, Victor Manuel and Vergara-Hernández, Hector Javier and Mihalcea, Elena and Villalobos-Brito, Julio and Alvarado-Hernandez, Francisco and Cabezas-Villa, Jose Luis and González-Gómez, Gilberto and Machado-López, Mario Misael and Olmos, Luis},
title = {Effect of Sintering Temperature on Densification, Microstructure, and Corrosion Behavior of Ti6Al4V/20Cu Composites Fabricated by Powder Metallurgy},
journal = {Materials},
year = {2026},
volume = {19},
number = {14},
pages = {2979},
doi = {10.3390/ma19142979}
}
EUVIMED