EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Analysis of Mechanical Properties of Cellular Structures Under Static Tensile Loading in Standardized Specimens Manufactured by Photopolymerization

Mateusz Rudnik iD, Mateusz Bronis iD, Mehmet Şükrü Adin iD, Nergizhan Anaç iD

Materials · 08.07.2026 · 19 (14) · 2945

DOI: 10.3390/ma19142945 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 08.07.2026. Verfasst von Mateusz Rudnik und 3 weiteren Autor:innen. Beteiligte Einrichtung: Department of Machine Design and Machining, Kielce University of Technology, 25314 Kielce, Poland. Die Arbeit wurde bisher 4-mal zitiert (Crossref) und nennt 27 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This study investigates the mechanical behavior and anisotropy of cellular structures fabricated using PolyJet Matrix (PJM) technology from RGD 720 photopolymer resin. Standard ISO 527 specimens were produced at build orientations of 0°, 45°, and 90° to evaluate the influence of printing direction on tensile properties. Based on these results, the optimal 0° orientation was selected for further analysis of cellular structures, including hexagonal, spiral, and quasi-self-similar geometries, manufactured in both unfilled and silicone-filled configurations. Static tensile tests were performed to determine load–displacement characteristics, maximum load, and deformation behavior. The results reveal a strong dependence of mechanical properties on build orientation, with the highest strength observed at 0° and the lowest at 90°, confirming significant material anisotropy. This behavior was further quantified using first- and second-order anisotropy coefficients derived from experimental data. The introduction of silicone filling improved load-bearing capacity, reduced variability, and promoted a more ductile failure mechanism. Among the analyzed geometries, quasi-self-similar structures exhibited the best mechanical performance, while unfilled structures showed lower strength and higher deformation. The findings demonstrate that both build orientation and structural design are critical factors in optimizing the mechanical properties of additively manufactured components and provide a basis for designing tailored cellular structures for engineering applications.

Schlagwörter

Stichwörter der Autor:innen

PolyJet Matrixadditive manufacturingcellular structuresmechanical propertiesphotopolymerizationstatic tensile test

Autor:innen und Institutionen

  • Department of Machine Design and Machining, Kielce University of Technology, 25314 Kielce, Poland.
  • Besiri OSB Vocational School, Batman University, Batman 72060, Turkey.
  • Faculty of Engineering, Zonguldak Bülent Ecevit University, Zonguldak 67100, Turkey.

ORCID-Profile: Mateusz Rudnik, Mateusz Bronis, Mehmet Şükrü Adin, Nergizhan Anaç

Zitieren

APA

Rudnik, M., Bronis, M., Adin, M. Ş., & Anaç, N. (2026). Analysis of Mechanical Properties of Cellular Structures Under Static Tensile Loading in Standardized Specimens Manufactured by Photopolymerization. Materials, 19(14), 2945. https://doi.org/10.3390/ma19142945

Vancouver

Rudnik M, Bronis M, Adin MŞ, Anaç N. Analysis of Mechanical Properties of Cellular Structures Under Static Tensile Loading in Standardized Specimens Manufactured by Photopolymerization. Materials. 2026;19(14):2945. doi:10.3390/ma19142945

BibTeX
@article{Rudnik2026,
  author = {Rudnik, Mateusz and Bronis, Mateusz and Adin, Mehmet Şükrü and Anaç, Nergizhan},
  title = {Analysis of Mechanical Properties of Cellular Structures Under Static Tensile Loading in Standardized Specimens Manufactured by Photopolymerization},
  journal = {Materials},
  year = {2026},
  volume = {19},
  number = {14},
  pages = {2945},
  doi = {10.3390/ma19142945}
}
Kostenlos starten →