Effects of Heat Treatment Procedures and Diamond Burnishing on Tensile Properties and Surface Integrity of Additively Manufactured 17-4PH Steel Cylindrical Parts
Materials · 22.05.2026 · 19 (11) · 2192
DOI: 10.3390/ma19112192 ↗Kurz gefasst
Fachartikel in der Zeitschrift Materials, online erschienen am 22.05.2026. Verfasst von Galya Duncheva und 7 weiteren Autor:innen. Beteiligte Einrichtung: Department of Material Science and Mechanics of Materials, Technical University of Gabrovo, 5300 Gabrovo, Bulgaria. Die Arbeit nennt 49 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: European Regional Development Fund under the Operational Program "Scientific Research, In-novation and Digitization for Smart Transformation 2021-2027".
Abstract (Originalsprache)
This article presents a new combined post-processing concept to improve the quality of laser powder bed fusion (LPBF) of 17-4PH stainless steel (SS) cylindrical parts fabricated from N2-atomised LaserForm 17-4PH (B) powder. The concept is based on consecutive heat treatment procedures and diamond burnishing (DB) processes. A two-stage study was conducted. The first stage was an LPBF process experiment. The following combination of LPBF parameter values was selected after optimisation: a laser power of P=150 W, laser scanning speed of v = 1200 mm/s, and layer thickness of t=40 μm. In the second stage, this combination was used to evaluate the effects of two heat treatment procedures (HT1 and HT2) and two DB processes (using burnishing forces of 100 N and 300 N) on the tensile properties and surface integrity of LPBF 17-4PH SS cylindrical samples. The HT2 procedure, including annealing (1200∘, 4 h), solution treatment (1060∘, 1 h), cooling (−70 ∘C,2 h), and ageing (482∘, 4 h) led to yield limit, tensile strength, and Vickers hardness values of YL=1071 MPa, TS=1410 MPa, and 523 HV, respectively. The concept presented takes advantage of the combination of the transformation, precipitation and strain-hardening effects. The combined effect was most pronounced in the samples subjected to the HT2 procedure and subsequent DB (300 N), for which a retained austenite fraction of 6.93%, surface microhardness of 563 HV0.05 and the maximum values of the compressive axial and hoop RSs of −1426.3 MPa and −1095.9 MPa, respectively, were measured.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Department of Material Science and Mechanics of Materials, Technical University of Gabrovo, 5300 Gabrovo, Bulgaria.
- Center of Competence "Smart Mechatronic, Eco-and Energy-Saving Systems and Technologies", Technical University of Gabrovo, 5300 Gabrovo, Bulgaria.
- Department of Material Sciences, Technical University of Varna, 9010 Varna, Bulgaria.
- Department of Industrial Technologies and Design, Technical University of Gabrovo, 5300 Gabrovo, Bulgaria.
ORCID-Profile: Galya Duncheva, Jordan Maximov, Vladimir Dunchev, Angel Anchev, Vladimir Todorov, Kalin Anastasov, Hristian Mitev
Förderung
- European Regional Development Fund under the Operational Program "Scientific Research, In-novation and Digitization for Smart Transformation 2021-2027"
Zitieren
APA
Duncheva, G., Maximov, J., Dunchev, V., Anchev, A., Todorov, V., Argirov, Y., Anastasov, K., & Mitev, H. (2026). Effects of Heat Treatment Procedures and Diamond Burnishing on Tensile Properties and Surface Integrity of Additively Manufactured 17-4PH Steel Cylindrical Parts. Materials, 19(11), 2192. https://doi.org/10.3390/ma19112192
Vancouver
Duncheva G, Maximov J, Dunchev V, Anchev A, Todorov V, Argirov Y, et al. Effects of Heat Treatment Procedures and Diamond Burnishing on Tensile Properties and Surface Integrity of Additively Manufactured 17-4PH Steel Cylindrical Parts. Materials. 2026;19(11):2192. doi:10.3390/ma19112192
BibTeX
@article{Duncheva2026,
author = {Duncheva, Galya and Maximov, Jordan and Dunchev, Vladimir and Anchev, Angel and Todorov, Vladimir and Argirov, Yaroslav and Anastasov, Kalin and Mitev, Hristian},
title = {Effects of Heat Treatment Procedures and Diamond Burnishing on Tensile Properties and Surface Integrity of Additively Manufactured 17-4PH Steel Cylindrical Parts},
journal = {Materials},
year = {2026},
volume = {19},
number = {11},
pages = {2192},
doi = {10.3390/ma19112192}
}
EUVIMED