EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Optimization of Aging Temperature and Heat-Treatment Pathways in Additively Manufactured 17-4PH Stainless Steel

Hobyung Chae iD, Sangyeob Lim, Taeho Lee, Eunjoo Shin, Joowon Suh, Suk Hoon Kang, Soo Yeol Lee

Materials · 08.12.2023 · 16 (24) · 7557

DOI: 10.3390/ma16247557 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 08.12.2023. Verfasst von Hobyung Chae und 6 weiteren Autor:innen. Beteiligte Einrichtung: Neutron Science Division, Korea Atomic Energy Research Institute, Daejeon 34057, Republic of Korea. Die Arbeit wurde bisher 15-mal zitiert (Crossref) und nennt 29 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: National Research Foundation of Korea, Ministry of Trade, Industry and Energy, Korea Institute of Energy Technology Evaluation and Planning.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This study investigates the tensile behaviors of additively manufactured (AM) 17-4PH stainless steels heat-treated within various temperature ranges from 400 °C to 700 °C in order to identify the effective aging temperature. Despite an aging treatment of 400–460 °C increasing the retained austenite content, an enhancement of the tensile properties was achieved without a strength-ductility trade-off owing to precipitation hardening by the Cu particles. Due to the intricate evolution of the microstructure, aging treatments above 490 °C led to a loss in yield strength and ductility. A considerable rise in strength and a decrease in ductility were brought about by the increase in the fraction of precipitation-hardened martensitic matrix in aging treatments over 640 °C. The impact of heat-treatment pathways on aging effectiveness and tensile anisotropy was then examined. Direct aging at 482 °C for an hour had hardly any effect on wrought 17-4PH, but it increased the yield strength of AM counterparts from 436–457 to 588–604 MPa. A solid-solution treatment at 1038 °C for one hour resulted in a significant drop in the austenite fraction, which led to an increase in the yield (from 436–457 to 841–919 MPa) and tensile strengths (from 1106–1127 to 1254–1256 MPa) with a sacrifice in ductility. Improved strength and ductility were realized by a solid-solution followed by an aging treatment, achieving 1371–1399 MPa. The tensile behaviors of AM 17-4PH were isotropic both parallel and perpendicular to the building direction.

Schlagwörter

Stichwörter der Autor:innen

17-4PH stainless steeladditive manufacturingheat-treatment

Autor:innen und Institutionen

  • Neutron Science Division, Korea Atomic Energy Research Institute, Daejeon 34057, Republic of Korea.
  • Nuclear Materials Division, Korea Atomic Energy Research Institute, Daejeon 34057, Republic of Korea.
  • Department of Materials Science and Engineering, Chungnam National University, Daejeon 34134, Republic of Korea.

ORCID-Profile: Hobyung Chae

Förderung

  • National Research Foundation of Korea
  • Ministry of Trade, Industry and Energy
  • Korea Institute of Energy Technology Evaluation and Planning
  • Korea Atomic Energy Research Institute
  • National Research Foundation (NRF) grant funded by the Korean government
  • Korea Institute for Advancement of Technology (KIAT)
  • Ministry of Trade, Industry, and Energy (MOTIE)
  • Korea Atomic Energy Research Institute R&D program

Zitieren

APA

Chae, H., Lim, S., Lee, T., Shin, E., Suh, J., Kang, S. H., & Lee, S. Y. (2023). Optimization of Aging Temperature and Heat-Treatment Pathways in Additively Manufactured 17-4PH Stainless Steel. Materials, 16(24), 7557. https://doi.org/10.3390/ma16247557

Vancouver

Chae H, Lim S, Lee T, Shin E, Suh J, Kang SH, et al. Optimization of Aging Temperature and Heat-Treatment Pathways in Additively Manufactured 17-4PH Stainless Steel. Materials. 2023;16(24):7557. doi:10.3390/ma16247557

BibTeX
@article{Chae2023,
  author = {Chae, Hobyung and Lim, Sangyeob and Lee, Taeho and Shin, Eunjoo and Suh, Joowon and Kang, Suk Hoon and Lee, Soo Yeol},
  title = {Optimization of Aging Temperature and Heat-Treatment Pathways in Additively Manufactured 17-4PH Stainless Steel},
  journal = {Materials},
  year = {2023},
  volume = {16},
  number = {24},
  pages = {7557},
  doi = {10.3390/ma16247557}
}
Kostenlos starten →