EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Effect of Mn Content on the Microstructure, Mechanical Properties, and Damping Capacity of Mn-Cu Alloys

Bin Wu, Bibo Li iD, Zhaobo Wu, Fengshuang Lu, Ran Li, Xiaojun Zhang, Xinqing Zhao, Feiyu Zhao iD, Dongliang Zhao

Materials · 24.04.2026 · 19 (9) · 1742

DOI: 10.3390/ma19091742 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 24.04.2026. Verfasst von Bin Wu und 8 weiteren Autor:innen. Beteiligte Einrichtung: Central Iron and Steel Research Institute, Beijing 100081, China. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 31 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Gentral Iron and Steel Research Institute R&D special fund, Gentral Iron and Steel Research Institute R&D special fund.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This study investigated the influence of Mn content (70 wt.%, 75 wt.%, and 80 wt.%) on the microstructure, mechanical properties and damping capacity of Mn-Cu alloys using X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), mechanical testing and dynamic mechanical analysis (DMA). The results indicate that during cooling after aging, the Mn-Cu alloy undergoes martensitic transformation, resulting in a dual-phase structure of fcc and fct. The 70 wt.% Mn alloy exhibits a mixed-grain structure with mostly long, straight twin bands, while the 75 wt.% and 80 wt.% Mn alloys consist of fine equiaxed grains with mostly intersecting twin bands. The microstructure determines the properties of the alloy. As the Mn content increases, the mechanical properties initially increase and then decrease, and the 75 wt.% Mn alloy has the best mechanical performance (UTS = 534 MPa, YS = 263 MPa). In contrast, the damping capacity shows a decreasing trend, and the 70 wt.% Mn alloy exhibits the best damping capacity (tanδ = 0.064). The main damping peak of tanδ in Mn-Cu alloys is derived from the relaxation of the twin boundaries, and the less obvious secondary peak is the internal friction peak of martensitic transformation.

Schlagwörter

Stichwörter der Autor:innen

Mn contentMn-Cu alloysdamping capacityfcc-fct phasetwin boundaries

Autor:innen und Institutionen

  • Central Iron and Steel Research Institute, Beijing 100081, China.
  • School of Materials Science and Engineering, Beihang University, Beijing 100191, China.
  • China Iron & Steel Research Institute Group Co., Ltd., Beijing 100081, China.

ORCID-Profile: Bibo Li, Feiyu Zhao

Förderung

  • Gentral Iron and Steel Research Institute R&D special fund
  • Gentral Iron and Steel Research Institute R&D special fund

Zitieren

APA

Wu, B., Li, B., Wu, Z., Lu, F., Li, R., Zhang, X., Zhao, X., Zhao, F., & Zhao, D. (2026). Effect of Mn Content on the Microstructure, Mechanical Properties, and Damping Capacity of Mn-Cu Alloys. Materials, 19(9), 1742. https://doi.org/10.3390/ma19091742

Vancouver

Wu B, Li B, Wu Z, Lu F, Li R, Zhang X, et al. Effect of Mn Content on the Microstructure, Mechanical Properties, and Damping Capacity of Mn-Cu Alloys. Materials. 2026;19(9):1742. doi:10.3390/ma19091742

BibTeX
@article{Wu2026,
  author = {Wu, Bin and Li, Bibo and Wu, Zhaobo and Lu, Fengshuang and Li, Ran and Zhang, Xiaojun and Zhao, Xinqing and Zhao, Feiyu and Zhao, Dongliang},
  title = {Effect of Mn Content on the Microstructure, Mechanical Properties, and Damping Capacity of Mn-Cu Alloys},
  journal = {Materials},
  year = {2026},
  volume = {19},
  number = {9},
  pages = {1742},
  doi = {10.3390/ma19091742}
}
Kostenlos starten →