EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

The Effect of Shot Peening on Corrosion Resistance of 18Ni300 Maraging Steel Manufactured by LPBF

Ji-Min Yun, Ho-Seok Nam, Ki-Hang Shin, Kwon-Hoo Kim iD, Ki-Woo Nam iD

Materials · 17.04.2026 · 19 (8) · 1619

DOI: 10.3390/ma19081619 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 17.04.2026. Verfasst von Ji-Min Yun und 4 weiteren Autor:innen. Beteiligte Einrichtung: Department of Marine Design Convergence Engineering, Pukyong National University, Busan 48513, Republic of Korea. Die Arbeit nennt 57 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: National Research Foundation of Korea(NRF) grant funded by the Korea government(MSIT), Korea government, Brain Korea 21 Program for Leading Universities and Students (BK21 FOUR) MADEC Marine Designeering Education Research Group.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This study investigated the correlation between mechanical strengthening and electrochemical corrosion behavior in 18Ni300 maraging steel fabricated via laser powder bed fusion (LPBF). To evaluate the impact of post-processing, specimens were analyzed under four conditions: solution treated (S), solution peened (SP), solution aged (SA), and solution aged peened (SAP). The aging treatment (490 °C for 6 h) effectively enhanced the corrosion resistance by homogenizing the martensitic matrix and promoting the formation of a stable passive film, resulting in the lowest corrosion current density (icorr of 1.716 × 10−6 A/cm2). In contrast, the application of shot peening after aging (SAP) significantly degraded the corrosion resistance, characterized by the most negative corrosion potential (Ecorr of −0.374 V and a 2.4 times increase in icorr compared to the SA condition. Quantitative analysis revealed that the 1250 MPa of compressive residual stress induced by peening increased the thermodynamic instability of the surface through extreme lattice distortion, thereby lowering the activation energy for anodic dissolution. Furthermore, the increased surface roughness (60.68 µm) expanded the effective electrochemical reaction area, acting as a kinetic accelerator for corrosion. The results demonstrate that while the SA process provides an optimal balance between microstructural stability and corrosion resistance, additional shot peening (SAP) imposes a significant corrosion penalty despite its mechanical benefits. This study concludes that for 18Ni300 maraging steel, the trade-off between mechanical reinforcement and electrochemical stability must be carefully managed, emphasizing the need for surface stabilization when high-intensity peening is applied in corrosive environments.

Schlagwörter

Stichwörter der Autor:innen

additive manufacturingcorrosion resistancemaraging steelshot peening

Autor:innen und Institutionen

  • Department of Marine Design Convergence Engineering, Pukyong National University, Busan 48513, Republic of Korea.
  • Busan Development Institue, Busan 47210, Republic of Korea.
  • Department of Metallurgical Engineering, Pukyong National University, Busan 48513, Republic of Korea.
  • Department of Materials Science and Engineering, Pukyong National University, Busan 48513, Republic of Korea.

ORCID-Profile: Kwon-Hoo Kim, Ki-Woo Nam

Förderung

  • National Research Foundation of Korea(NRF) grant funded by the Korea government(MSIT)
  • Korea government
  • Brain Korea 21 Program for Leading Universities and Students (BK21 FOUR) MADEC Marine Designeering Education Research Group

Zitieren

APA

Yun, J. M., Nam, H. S., Shin, K. H., Kim, K. H., & Nam, K. W. (2026). The Effect of Shot Peening on Corrosion Resistance of 18Ni300 Maraging Steel Manufactured by LPBF. Materials, 19(8), 1619. https://doi.org/10.3390/ma19081619

Vancouver

Yun JM, Nam HS, Shin KH, Kim KH, Nam KW. The Effect of Shot Peening on Corrosion Resistance of 18Ni300 Maraging Steel Manufactured by LPBF. Materials. 2026;19(8):1619. doi:10.3390/ma19081619

BibTeX
@article{Yun2026,
  author = {Yun, Ji-Min and Nam, Ho-Seok and Shin, Ki-Hang and Kim, Kwon-Hoo and Nam, Ki-Woo},
  title = {The Effect of Shot Peening on Corrosion Resistance of 18Ni300 Maraging Steel Manufactured by LPBF},
  journal = {Materials},
  year = {2026},
  volume = {19},
  number = {8},
  pages = {1619},
  doi = {10.3390/ma19081619}
}
Kostenlos starten →