EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Effect of Adhesive Type and Surface Preparation on the Debonding Behavior of Glass and Carbon Fiber Reinforced Epoxy Adhesive Joints

Paula Vigón iD, Antonio Argüelles, Miguel Lozano iD, Jaime Viña iD

Materials · 14.04.2026 · 19 (8) · 1561

DOI: 10.3390/ma19081561 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 14.04.2026. Verfasst von Paula Vigón und 3 weiteren Autor:innen. Beteiligte Einrichtung: Department of Construction and Manufacturing Engineering, Edificio Departamental Oeste, n 7, University of Oviedo, 33203 Gijón, Spain. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 49 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: the Vice-Rectorate for Research at the University of Oviedo through the Research Support and Promotion Plan, the Spanish Ministry of Science and Innovation.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

In this work, the debonding behavior under quasi-static Mode I fracture loading of adhesive joints made on two types of composite materials with the same epoxy matrix and unidirectional carbon or glass fiber reinforcement was analyzed. Standard DCB tests were used to quantify the influence of adhesive type and substrate surface preparation on interlaminar fracture toughness. For the fabrication of the joints under study, three commercial structural adhesives from different manufacturers were selected, two epoxy-based and one acrylic-based. Substrate surface preparation was carried out using three different procedures: manual abrasion, sanding with P220 Al2O3 sandpaper, grit blasting with Al2O3, and peel ply PA80 polyamide fabric. The experimental results revealed the same trend for both epoxy-based adhesives: sanding provided the best results, regardless of the substrate used. Surface preparation by grit blasting proved highly sensitive to the applied parameters, generally yielding poorer results than manual sanding. Surface preparation using PA80 peel ply fabric may be a viable option. However, its main drawback is that it must be incorporated during composite manufacturing. The results demonstrate that fracture performance is governed by the interaction between adhesive chemistry and surface morphology rather than by surface roughness alone.

Schlagwörter

Stichwörter der Autor:innen

CFRPMode Icarbon fiberdebondingfractureglass fibersurface preparation

Autor:innen und Institutionen

  • Department of Construction and Manufacturing Engineering, Edificio Departamental Oeste, n 7, University of Oviedo, 33203 Gijón, Spain.
  • School of Engineering and Technology (ESIT), Universidad Internacional de La Rioja (UNIR), 26006 Logroño, Spain.
  • Department of Materials Science and Metallurgical Engineering, Edificio Departamental Este, n3, University of Oviedo, 33203 Gijón, Spain.

ORCID-Profile: Paula Vigón, Miguel Lozano, Jaime Viña

Förderung

  • the Vice-Rectorate for Research at the University of Oviedo through the Research Support and Promotion Plan
  • the Spanish Ministry of Science and Innovation

Zitieren

APA

Vigón, P., Argüelles, A., Lozano, M., & Viña, J. (2026). Effect of Adhesive Type and Surface Preparation on the Debonding Behavior of Glass and Carbon Fiber Reinforced Epoxy Adhesive Joints. Materials, 19(8), 1561. https://doi.org/10.3390/ma19081561

Vancouver

Vigón P, Argüelles A, Lozano M, Viña J. Effect of Adhesive Type and Surface Preparation on the Debonding Behavior of Glass and Carbon Fiber Reinforced Epoxy Adhesive Joints. Materials. 2026;19(8):1561. doi:10.3390/ma19081561

BibTeX
@article{Vign2026,
  author = {Vigón, Paula and Argüelles, Antonio and Lozano, Miguel and Viña, Jaime},
  title = {Effect of Adhesive Type and Surface Preparation on the Debonding Behavior of Glass and Carbon Fiber Reinforced Epoxy Adhesive Joints},
  journal = {Materials},
  year = {2026},
  volume = {19},
  number = {8},
  pages = {1561},
  doi = {10.3390/ma19081561}
}
Kostenlos starten →