EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Influence of Microstructure Evolution on Tribological and Corrosion Performances of QPQ-Treated 40Cr Steel

Jingtao Yang, Chengyuan Ni, Sen Feng, Chengdong Xia iD, Minghua Yin

Materials · 13.04.2026 · 19 (8) · 1557

DOI: 10.3390/ma19081557 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 13.04.2026. Verfasst von Jingtao Yang und 4 weiteren Autor:innen. Beteiligte Einrichtung: College of Mechanical Engineering, Zhejiang University of Technology, Hangzhou 310023, China. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 54 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Quzhou Municipal Science and Technology Bureau, Zhejiang Key Laboratory of Intelligent Manufacturing for Aerodynamic Equipment, Zhejiang Provincial Natural Science Foundation.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Quench–polish–quench (QPQ) of 40Cr steel was performed to improve its tribological properties and corrosion resistance, thereby enhancing the service performance of components such as gears and bearings. The 40Cr steel was treated by QPQ at 580 °C and 620 °C for 90 or 120 min. Optical microscopy (OM, Sunny Group, Ningbo, China), scanning electron microscopy (SEM, Hitachi, Tokyo, Japan), and X-ray diffraction (XRD Rigaku Corporation, Tokyo, Japan) were used to characterise the microstructure and phase constitution. Ball-on-disk tribometry, electrochemical tests, and salt spray tests in 3.5 wt.% NaCl evaluated surface performance. At 580 °C, a composite structure of Fe3O4 and ε-Fe2−3N formed on the surface. When the temperature rose to 620 °C, ε-Fe2–3N gradually transformed into γ′-Fe4N. Within the scope of this study, the diffusion layer depth exhibits an approximately linear relationship with increasing processing temperature and holding time, and the surface hardness is 67–112% higher than that of the untreated sample. After QPQ treatment, the wear mechanism changed from adhesive wear to abrasive wear. However, under the treatment conditions of 620 °C × 120 min, brittle surface spalling increased roughness, thereby increasing the coefficient of friction. As treatment time increases, nitrogen atoms continue to diffuse outward as Fe2N transforms to the γ′ phase. This increases the composite layer’s porosity and decreases its corrosion resistance. The best corrosion resistance was observed at 580 °C for 120 min, with a corrosion potential of −0.4325 V, corrosion current density of 1.80 × 10−6 A·cm−2, and polarisation resistance of 24,500 Ω. Corrosion performance depends on overall surface integrity. Porosity morphology strongly influences this property. For 40Cr steel, the results show that surface properties are primarily determined by the quality of the compound layer’s microstructure. Specifically, density, phase-composition stability, and defect control are more important than the commonly held view of layer thickness.

Schlagwörter

Stichwörter der Autor:innen

40CrQPQ treatmentcorrosion resistancemicrostructure evolutiontribological performance

Autor:innen und Institutionen

  • College of Mechanical Engineering, Zhejiang University of Technology, Hangzhou 310023, China.
  • Zhejiang Provincial Key Laboratory of Intelligent Manufacturing for Aerodynamic Equipment, Quzhou 324000, China.
  • Zhejiang Zhongcheng Sliding Bearing Technology Co., Ltd., Quzhou 324000, China.

ORCID-Profile: Chengdong Xia

Förderung

  • Quzhou Municipal Science and Technology Bureau
  • Zhejiang Key Laboratory of Intelligent Manufacturing for Aerodynamic Equipment
  • Zhejiang Provincial Natural Science Foundation
  • Joint Funds of the Zhejiang Provincial Natural Science Foundation of China

Zitieren

APA

Yang, J., Ni, C., Feng, S., Xia, C., & Yin, M. (2026). Influence of Microstructure Evolution on Tribological and Corrosion Performances of QPQ-Treated 40Cr Steel. Materials, 19(8), 1557. https://doi.org/10.3390/ma19081557

Vancouver

Yang J, Ni C, Feng S, Xia C, Yin M. Influence of Microstructure Evolution on Tribological and Corrosion Performances of QPQ-Treated 40Cr Steel. Materials. 2026;19(8):1557. doi:10.3390/ma19081557

BibTeX
@article{Yang2026,
  author = {Yang, Jingtao and Ni, Chengyuan and Feng, Sen and Xia, Chengdong and Yin, Minghua},
  title = {Influence of Microstructure Evolution on Tribological and Corrosion Performances of QPQ-Treated 40Cr Steel},
  journal = {Materials},
  year = {2026},
  volume = {19},
  number = {8},
  pages = {1557},
  doi = {10.3390/ma19081557}
}
Kostenlos starten →