EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Effect of Changes in Plastic Flow During Non-Steady State Deformation on Force Behavior in Micro-Extrusion of Pure Copper

Keisuke Sugiyama, Masato Ito, Kenichi Yaguchi, Tatsuya Funazuka iD, Tomomi Shiratori iD

Materials · 30.03.2026 · 19 (7) · 1374

DOI: 10.3390/ma19071374 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 30.03.2026. Verfasst von Keisuke Sugiyama und 4 weiteren Autor:innen. Beteiligte Einrichtung: Mitsubishi Materials Corporation, 7-147 Shimoishito, Kitamoto 364-0028, Saitama, Japan. Die Arbeit nennt 18 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

In recent years, copper-based conductive and heat dissipation components have required fine structures for miniaturization and enhanced functionality. Micro-forming is an excellent processing method characterized by high productivity and suitability for mass production. Since small workpieces can be formed within a short stroke in micro-extrusion, it is important to understand the deformation behavior immediately after the start of extrusion. However, before steady state is attained, the evolution of microstructure and plastic flow with stroke progression during non-steady-state deformation has not yet been sufficiently clarified. In this study, to investigate the effect of changes in plastic flow on force behavior, micro-extrusion tests were conducted using pure copper. The geometric and crystallographic characteristics of the deformation structure were then analyzed. The extrusion force behavior exhibited three distinct stages, including a peak of the force. The force peak was attributed to changes in plastic flow associated with the deformation structure formed at the sample tip immediately after the start of extrusion. This change leads to the evolution of the effective extrusion ratio, which significantly influences the force response during non-steady-state deformation.

Schlagwörter

Stichwörter der Autor:innen

deformation behaviormicro-formingplastic deformationpure coppersize effect

Autor:innen und Institutionen

  • Mitsubishi Materials Corporation, 7-147 Shimoishito, Kitamoto 364-0028, Saitama, Japan.
  • Department of Mechanical Engineering, Toyama University, 3190 Gofuku, Toyama-shi 930-8555, Toyama, Japan.

ORCID-Profile: Tatsuya Funazuka, Tomomi Shiratori

Zitieren

APA

Sugiyama, K., Ito, M., Yaguchi, K., Funazuka, T., & Shiratori, T. (2026). Effect of Changes in Plastic Flow During Non-Steady State Deformation on Force Behavior in Micro-Extrusion of Pure Copper. Materials, 19(7), 1374. https://doi.org/10.3390/ma19071374

Vancouver

Sugiyama K, Ito M, Yaguchi K, Funazuka T, Shiratori T. Effect of Changes in Plastic Flow During Non-Steady State Deformation on Force Behavior in Micro-Extrusion of Pure Copper. Materials. 2026;19(7):1374. doi:10.3390/ma19071374

BibTeX
@article{Sugiyama2026,
  author = {Sugiyama, Keisuke and Ito, Masato and Yaguchi, Kenichi and Funazuka, Tatsuya and Shiratori, Tomomi},
  title = {Effect of Changes in Plastic Flow During Non-Steady State Deformation on Force Behavior in Micro-Extrusion of Pure Copper},
  journal = {Materials},
  year = {2026},
  volume = {19},
  number = {7},
  pages = {1374},
  doi = {10.3390/ma19071374}
}
Kostenlos starten →