EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Influence of Substrate Manufacturing Route on HiPIMS TiAlSiN-Coated AISI 316L Stainless Steel Produced by Laser Powder Bed Fusion

Marek Kočiško iD, Patrik Petroušek iD, Róbert Kočiško iD, Lukáš Štafura, Dávid Medveď, Róbert Džunda iD

Materials · 18.03.2026 · 19 (6) · 1184

DOI: 10.3390/ma19061184 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 18.03.2026. Verfasst von Marek Kočiško und 5 weiteren Autor:innen. Beteiligte Einrichtung: Faculty of Manufacturing Technologies, Technical University of Kosice, Bayerova 1, 080 01 Presov, Slovakia. Die Arbeit wurde bisher 2-mal zitiert (Crossref) und nennt 50 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: NextGenerationEU through the Recovery and Resilience Plan for Slovakia, Slovak Research and Development Agency, Ministry of Education, Research, Development and Youth of the Slovak Republic.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Laser powder bed fusion has attracted increasing attention for the production of metallic substrates intended for surface functionalization by advanced physical vapor deposition coatings. This study investigates the influence of the substrate manufacturing route on the performance of titanium–aluminum–silicon nitride-coated AISI 316L stainless steel, with particular emphasis on substrates produced by laser powder bed fusion. Conventionally manufactured and additively manufactured AISI 316L substrates were coated with a titanium–aluminum–silicon nitride layer using high-power impulse magnetron sputtering. The substrates were characterized by tensile testing and microhardness measurements, while coating thickness and uniformity were evaluated using the crater ball method. The mechanical integrity of the coating–substrate system was assessed by progressive load scratch testing. The additively manufactured substrate exhibited a significantly higher yield strength (411 MPa) compared to the conventionally manufactured material (257 MPa), together with increased microhardness. The titanium–aluminum–silicon nitride coating showed a uniform thickness of 4.47 µm and a well-defined coating–substrate interface. Scratch tests revealed a delayed onset of coating damage on additively manufactured substrates, with the transition to severe adhesive failure occurring at higher normal loads compared to the conventionally manufactured substrate. These results demonstrate that AISI 316L stainless steel produced by laser powder bed fusion provides a mechanically robust substrate for titanium–aluminum–silicon nitride coatings deposited by high-power impulse magnetron sputtering, with favorable coating response under progressive loading conditions.

Schlagwörter

Stichwörter der Autor:innen

AISI 316L stainless steelHiPIMSTiAlSiN coatinglaser powder bed fusionmechanical propertiesmicrostructure

Autor:innen und Institutionen

  • Faculty of Manufacturing Technologies, Technical University of Kosice, Bayerova 1, 080 01 Presov, Slovakia.
  • Institute of Materials, Faculty of Materials, Metallurgy and Recycling, Technical University of Kosice, Letná 1/9, 042 00 Košice, Slovakia.
  • Institute of Materials Research, Slovak Academy of Sciences, Watsonova 47, 040 01 Košice, Slovakia.

ORCID-Profile: Marek Kočiško, Patrik Petroušek, Róbert Kočiško, Róbert Džunda

Förderung

  • NextGenerationEU through the Recovery and Resilience Plan for Slovakia
  • Slovak Research and Development Agency
  • Ministry of Education, Research, Development and Youth of the Slovak Republic
  • EU NextGenerationEU

Zitieren

APA

Kočiško, M., Petroušek, P., Kočiško, R., Štafura, L., Medveď, D., & Džunda, R. (2026). Influence of Substrate Manufacturing Route on HiPIMS TiAlSiN-Coated AISI 316L Stainless Steel Produced by Laser Powder Bed Fusion. Materials, 19(6), 1184. https://doi.org/10.3390/ma19061184

Vancouver

Kočiško M, Petroušek P, Kočiško R, Štafura L, Medveď D, Džunda R. Influence of Substrate Manufacturing Route on HiPIMS TiAlSiN-Coated AISI 316L Stainless Steel Produced by Laser Powder Bed Fusion. Materials. 2026;19(6):1184. doi:10.3390/ma19061184

BibTeX
@article{Koiko2026,
  author = {Kočiško, Marek and Petroušek, Patrik and Kočiško, Róbert and Štafura, Lukáš and Medveď, Dávid and Džunda, Róbert},
  title = {Influence of Substrate Manufacturing Route on HiPIMS TiAlSiN-Coated AISI 316L Stainless Steel Produced by Laser Powder Bed Fusion},
  journal = {Materials},
  year = {2026},
  volume = {19},
  number = {6},
  pages = {1184},
  doi = {10.3390/ma19061184}
}
Kostenlos starten →