Effect of Pulse Plasma Sintering Temperature on Microstructure and Mechanical Properties of Al2O3-Cu Composites
Materials · 12.03.2026 · 19 (6) · 1086
DOI: 10.3390/ma19061086 ↗Kurz gefasst
Fachartikel in der Zeitschrift Materials, online erschienen am 12.03.2026. Verfasst von Paulina Piotrkiewicz und 4 weiteren Autor:innen. Beteiligte Einrichtung: Faculty of Materials Science and Engineering, Warsaw University of Technology, 141 Woloska St., 02-507 Warsaw, Poland. Die Arbeit nennt 57 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Military University of Technology in Warsaw, Military University of Technology.
Abstract (Originalsprache)
Al2O3-Cu ceramic-metal composites containing 2.5 vol.% of a metallic phase were fabricated using the Pulse Plasma Sintering (PPS) method in order to evaluate the influence of sintering temperature on densification, microstructure, and mechanical performance. Consolidation was carried out at 1200 °C, 1250 °C, 1300 °C, and 1400 °C under uniaxial pressure with a short sintering time of 3 min. Regardless of the processing temperature, all composites exhibited very high relative densities exceeding 99% of the theoretical value, indicating the high efficiency of PPS in densifying Al2O3-Cu systems while suppressing copper leakage. X-ray diffraction confirmed the presence of only two phases, Al2O3 and Cu, with no secondary reaction products. Microstructural observations revealed irregular copper particles and areas of dispersed metallic phase, whose proportion decreased with increasing sintering temperature due to accelerated matrix densification and copper immobilization. Grain growth in the alumina matrix was strongly temperature-dependent, with the average equivalent grain diameter increasing from 0.49 µm at 1200 °C to 2.35 µm at 1400 °C. Hardness decreased from 19.5 ± 2.8 GPa to 12.2 ± 1.6 GPa with increasing temperature, whereas fracture toughness reached a maximum of 5.42 ± 0.65 MPa·m0.5 at 1400 °C. The highest strength under monotonic compression conditions was obtained for samples sintered at 1300 °C, indicating an optimal balance between densification and microstructural coarsening. These results demonstrate that PPS is an effective method for producing dense Al2O3-Cu composites with tailored microstructure and mechanical properties.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Faculty of Materials Science and Engineering, Warsaw University of Technology, 141 Woloska St., 02-507 Warsaw, Poland.
- Faculty of Mechanical Engineering, Military University of Technology, 2 Gen. S. Kaliskiego St., 00-908 Warsaw, Poland.
ORCID-Profile: Paulina Piotrkiewicz, Justyna Zygmuntowicz, Marcin Wachowski, Ireneusz Szachogłuchowicz
Förderung
- Military University of Technology in Warsaw
- Military University of Technology
Zitieren
APA
Piotrkiewicz, P., Zygmuntowicz, J., Wachowski, M., Szachogłuchowicz, I., & Kaszuwara, W. (2026). Effect of Pulse Plasma Sintering Temperature on Microstructure and Mechanical Properties of Al2O3-Cu Composites. Materials, 19(6), 1086. https://doi.org/10.3390/ma19061086
Vancouver
Piotrkiewicz P, Zygmuntowicz J, Wachowski M, Szachogłuchowicz I, Kaszuwara W. Effect of Pulse Plasma Sintering Temperature on Microstructure and Mechanical Properties of Al2O3-Cu Composites. Materials. 2026;19(6):1086. doi:10.3390/ma19061086
BibTeX
@article{Piotrkiewicz2026,
author = {Piotrkiewicz, Paulina and Zygmuntowicz, Justyna and Wachowski, Marcin and Szachogłuchowicz, Ireneusz and Kaszuwara, Waldemar},
title = {Effect of Pulse Plasma Sintering Temperature on Microstructure and Mechanical Properties of Al2O3-Cu Composites},
journal = {Materials},
year = {2026},
volume = {19},
number = {6},
pages = {1086},
doi = {10.3390/ma19061086}
}
EUVIMED