EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Thermal Deformation in Non-Planar Large-Scale Additive Manufacturing of ABS: Experimental and Finite Element Analysis

Mehmet Aladag iD, Engin Tek iD, Mehmet Ali Akeloglu iD, Adrian Dubicki iD, Izabela Zgłobicka iD, Omer Eyercioglu iD, Krzysztof J Kurzydlowski iD

Materials · 11.03.2026 · 19 (6) · 1064

DOI: 10.3390/ma19061064 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 11.03.2026. Verfasst von Mehmet Aladag und 6 weiteren Autor:innen. Beteiligte Einrichtung: Faculty of Mechanical Engineering, Bialystok University of Technology, Wiejska 45C, 15-351 Bialystok, Poland. Die Arbeit wurde bisher 3-mal zitiert (Crossref) und nennt 44 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Bialystok University of Technology, Bialystok University of Technology, Faculty of Mechanical Engineering, Poland.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

In this study, thermal deformation in non-planar, large-scale additive manufacturing (LSAM) was experimentally and numerically investigated. A Bézier-based non-planar build surface was fabricated by CNC machining, and a single layer of ABS was deposited using a hybrid LSAM system. Toolpaths with raster angles of 0° and 45° were generated for surface-conformal printing. Infrared thermography was employed to monitor the thermal history during deposition. A three-dimensional finite element model was developed to simulate transient heat transfer and thermally induced deformation. Experimental deformation was quantified by 3D scanning and compared with simulation results. The results show that the slope geometry strongly influences deformation direction: negative slopes promote contraction, whereas positive slopes lead to upward deflection. Maintaining the material temperature above the glass transition temperature significantly reduces skew deformation. The finite element method predictions demonstrate strong agreement with experimental measurements, with normalized root mean square errors (NRMSEs) of approximately 11% for thermal deformation and 10% for temperature history. The proposed framework enables prediction and mitigation of thermal warping in non-planar polymer additive manufacturing.

Schlagwörter

Stichwörter der Autor:innen

coatinghybrid large-scale additive manufacturingnon-planar printingnumerical simulationthermal deformation

Autor:innen und Institutionen

  • Faculty of Mechanical Engineering, Bialystok University of Technology, Wiejska 45C, 15-351 Bialystok, Poland.
  • Department of Electronics and Automation, Gedik Vocational School, Istanbul Gedik University, 34876 Istanbul, Türkiye.
  • Mechanical Engineering Department, Engineering Faculty, Gaziantep University, 27410 Gaziantep, Türkiye.

ORCID-Profile: Mehmet Aladag, Engin Tek, Mehmet Ali Akeloglu, Adrian Dubicki, Izabela Zgłobicka, Omer Eyercioglu, Krzysztof J Kurzydlowski

Förderung

  • Bialystok University of Technology
  • Bialystok University of Technology, Faculty of Mechanical Engineering, Poland

Zitieren

APA

Aladag, M., Tek, E., Akeloglu, M. A., Dubicki, A., Zgłobicka, I., Eyercioglu, O., & Kurzydlowski, K. J. (2026). Thermal Deformation in Non-Planar Large-Scale Additive Manufacturing of ABS: Experimental and Finite Element Analysis. Materials, 19(6), 1064. https://doi.org/10.3390/ma19061064

Vancouver

Aladag M, Tek E, Akeloglu MA, Dubicki A, Zgłobicka I, Eyercioglu O, et al. Thermal Deformation in Non-Planar Large-Scale Additive Manufacturing of ABS: Experimental and Finite Element Analysis. Materials. 2026;19(6):1064. doi:10.3390/ma19061064

BibTeX
@article{Aladag2026,
  author = {Aladag, Mehmet and Tek, Engin and Akeloglu, Mehmet Ali and Dubicki, Adrian and Zgłobicka, Izabela and Eyercioglu, Omer and Kurzydlowski, Krzysztof J},
  title = {Thermal Deformation in Non-Planar Large-Scale Additive Manufacturing of ABS: Experimental and Finite Element Analysis},
  journal = {Materials},
  year = {2026},
  volume = {19},
  number = {6},
  pages = {1064},
  doi = {10.3390/ma19061064}
}
Kostenlos starten →