EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Influence of Laser Cutting Parameters on the Microhardness, Roughness, and Microstructure of AISI 304, S355J2, and AlMg3 Alloys

Jaroslaw Selech iD, Grzegorz Burzynski, Dessie Tibebe iD, Dariusz Ulbrich iD, Piotr Banas

Materials · 07.01.2026 · 19 (2) · 240

DOI: 10.3390/ma19020240 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 07.01.2026. Verfasst von Jaroslaw Selech und 4 weiteren Autor:innen. Beteiligte Einrichtung: Institute of Machines and Motor Vehicles, Poznan University of Technology, 60-965 Poznan, Poland. Die Arbeit wurde bisher 4-mal zitiert (Crossref) und nennt 33 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Ministry of Science and Higher Education in Poland.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This study provides a comparative and material-specific assessment of how laser cutting parameters affect the surface integrity of three commonly used engineering alloys, thereby extending the current knowledge beyond single-material analyses. The main objective was to quantify and relate changes in surface roughness, microhardness, and microstructure to variations in laser cutting conditions for S355J2 steel, AISI 304 steel, and AlMg3 aluminum alloy. Variable cutting parameters were applied, including cutting speed, assist gas type and pressure, as well as laser beam power, and their combined effect on the thickness of the remelted and heat-affected zones was evaluated. The results show clear material-dependent trends: S355J2 steel exhibited the lowest surface roughness but the most pronounced surface hardening, with maximum microhardness values reaching approximately 700 HV 0.1 in a relatively narrow heat-affected zone, whereas AISI 304 showed a distinct edge-hardening effect with more moderate roughness. In contrast, the AlMg3 alloy developed a clearly visible remelted layer and a refined, fine-grained microstructure, accompanied by much lower hardness levels but a more diffuse heat-affected zone. These findings provide original, comparative guidelines for selecting laser cutting parameters tailored to specific materials, enabling the optimization of edge quality and surface properties in industrial applications.

Schlagwörter

Stichwörter der Autor:innen

AISI 304 steelAlMg3S355J2 steelcuttingmicrohardnesssurface roughness

Autor:innen und Institutionen

  • Institute of Machines and Motor Vehicles, Poznan University of Technology, 60-965 Poznan, Poland.
  • WKS Spawalnik T. G. Burzyńscy, 64-800 Chodzież, Poland.
  • College of Natural and Computational Science, University of Gondar, Gondar P.O. Box 196, Ethiopia.

ORCID-Profile: Jaroslaw Selech, Dessie Tibebe, Dariusz Ulbrich

Förderung

  • Ministry of Science and Higher Education in Poland

Zitieren

APA

Selech, J., Burzynski, G., Tibebe, D., Ulbrich, D., & Banas, P. (2026). Influence of Laser Cutting Parameters on the Microhardness, Roughness, and Microstructure of AISI 304, S355J2, and AlMg3 Alloys. Materials, 19(2), 240. https://doi.org/10.3390/ma19020240

Vancouver

Selech J, Burzynski G, Tibebe D, Ulbrich D, Banas P. Influence of Laser Cutting Parameters on the Microhardness, Roughness, and Microstructure of AISI 304, S355J2, and AlMg3 Alloys. Materials. 2026;19(2):240. doi:10.3390/ma19020240

BibTeX
@article{Selech2026,
  author = {Selech, Jaroslaw and Burzynski, Grzegorz and Tibebe, Dessie and Ulbrich, Dariusz and Banas, Piotr},
  title = {Influence of Laser Cutting Parameters on the Microhardness, Roughness, and Microstructure of AISI 304, S355J2, and AlMg3 Alloys},
  journal = {Materials},
  year = {2026},
  volume = {19},
  number = {2},
  pages = {240},
  doi = {10.3390/ma19020240}
}
Kostenlos starten →