Impact of Substrate Preheating on Weld Quality, Microstructure, Corrosion Resistance, and Mechanical Properties in Gas Tungsten Arc Welding of UNS S32750 Super Duplex Stainless Steel
Materials · 06.01.2026 · 19 (2) · 221
DOI: 10.3390/ma19020221 ↗Kurz gefasst
Fachartikel in der Zeitschrift Materials, online erschienen am 06.01.2026. Verfasst von Eli Jorge da Cruz Junior und 7 weiteren Autor:innen. Beteiligte Einrichtung: Department of Industry, São Paulo Federal Institute of Education, Science and Technology, Campus Itapetininga, Av. João Olímpio de Oliveira 1561, Ita…. Die Arbeit wurde bisher 2-mal zitiert (Crossref) und nennt 32 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Fundação de Amparo à Pesquisa do Estado de São Paulo, FAPESP—São Paulo Research Foundation, Brazil.
Abstract (Originalsprache)
Super duplex stainless steels (SDSS) are materials known for their exceptional mechanical strength and high resistance to corrosion due to their dual- phase microstructure consisting of ferrite and austenite in roughly equal proportions. However, the Gas Tungsten Arc Welding (GTAW) process used to join SDSS often causes microstructural imbalances, mainly ferritic structures, or the formation of harmful intermetallic phases, which can weaken the material’ s desirable properties. This study examines the effect of substrate preheating on the microstructure, mechanical properties, and corrosion resistance of UNS S32750 SDSS welds produced by GTAW. Preheating the substrate was considered as a strategy to improve phase balance in the fusion zone by extending the time within the ferrite- to- austenite transformation temperature range, thus slowing the cooling rates. Four conditions were tested: welding at room temperature (RT) and preheating to 100 °C (T100), 200 °C (T200), and 300 °C (T300). Welding parameters remained constant. The fusion zone microstructure was analyzed using metallographic techniques, while mechanical properties were evaluated through microhardness tests. Corrosion resistance was assessed with potential dynamic polarization in a 3.5% NaCl solution. The results showed significant improvements in microstructural balance with higher preheating temperatures. The austenite volume fraction in the fusion zone increased from about 16% at RT to 42% at T 300. Mechanical testing indicated a decrease in microhardness from 341 HV at RT to 314 HV at T 300, reflecting the increased austenite content and its associated toughness. Corrosion tests demonstrated enhanced resistance under preheated conditions, with T 300 exhibiting the highest corrosion potential and the lowest corrosion current, nearing the performance of the base metal. These findings suggest that preheating is a practical, cost- effective method for optimizing the GTAW process for SDSS, eliminating the need for expensive filler materials and stabilizing the microstructure elements.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Department of Industry, São Paulo Federal Institute of Education, Science and Technology, Campus Itapetininga, Av. João Olímpio de Oliveira 1561, Itapetininga 18202-000, SP, Brazil.
- Department of Mechanical Engineering, Sao Paulo State University, Avenue Brasil 56, Ilha Solteira 15385-000, SP, Brazil.
- Department of Industrial Engineering, University of Padua, Via Gradenigo, 6/a, 35131 Padova, Italy.
ORCID-Profile: Eli Jorge da Cruz Junior, Francisco Mateus Faria de Almeida Varasquim, Vicente Afonso Ventrella, Irene Calliari
Förderung
- Fundação de Amparo à Pesquisa do Estado de São Paulo
- FAPESP—São Paulo Research Foundation, Brazil
Zitieren
APA
da Cruz Junior, E. J., Ribeiro, R. H., Varasquim, F. M. F. A., Carvalho, F. O., Santiago, L. F. F., Lemos, G. P., Ventrella, V. A., & Calliari, I. (2026). Impact of Substrate Preheating on Weld Quality, Microstructure, Corrosion Resistance, and Mechanical Properties in Gas Tungsten Arc Welding of UNS S32750 Super Duplex Stainless Steel. Materials, 19(2), 221. https://doi.org/10.3390/ma19020221
Vancouver
da Cruz Junior EJ, Ribeiro RH, Varasquim FMFA, Carvalho FO, Santiago LFF, Lemos GP, et al. Impact of Substrate Preheating on Weld Quality, Microstructure, Corrosion Resistance, and Mechanical Properties in Gas Tungsten Arc Welding of UNS S32750 Super Duplex Stainless Steel. Materials. 2026;19(2):221. doi:10.3390/ma19020221
BibTeX
@article{daCruzJunior2026,
author = {da Cruz Junior, Eli Jorge and Ribeiro, Raul Henrique and Varasquim, Francisco Mateus Faria de Almeida and Carvalho, Fábio Oliveira and Santiago, Luiz Fernando Frezzatti and Lemos, Gabriela Pereira and Ventrella, Vicente Afonso and Calliari, Irene},
title = {Impact of Substrate Preheating on Weld Quality, Microstructure, Corrosion Resistance, and Mechanical Properties in Gas Tungsten Arc Welding of UNS S32750 Super Duplex Stainless Steel},
journal = {Materials},
year = {2026},
volume = {19},
number = {2},
pages = {221},
doi = {10.3390/ma19020221}
}
EUVIMED