The Influence of Model Orientation on the Surface Roughness of Polymeric Models Produced by FFF, mSLA, PJ, and SLS Methods
Materials · 12.12.2025 · 18 (24) · 5600
DOI: 10.3390/ma18245600 ↗Kurz gefasst
Fachartikel in der Zeitschrift Materials, online erschienen am 12.12.2025. Verfasst von Anna Bazan und 5 weiteren Autor:innen. Beteiligte Einrichtung: Faculty of Mechanical Engineering and Aeronautics, Rzeszów University of Technology, 35-959 Rzeszów, Poland. Die Arbeit wurde bisher 5-mal zitiert (Crossref) und nennt 65 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Minister of Science and Higher Education Republic of Poland.
Abstract (Originalsprache)
The research methodology involved creating a 3D sample model that featured both flat and cylindrical surfaces inclined at angles ranging from 0° to 90° relative to the XY plane. The study investigated the surface topography of additively manufactured samples produced using various technologies, including Fused Filament Fabrication (FFF), masked Stereolithography (mSLA), PolyJet (PJ), and Selective Laser Sintering (SLS). The focus was on how material type, print angle, and measurement location influenced the results. The materials used in the study included PLA, PETG, acrylic resins, PA2200, and VeroClear. Due to the optical properties of the materials used, measurements were carried out on replicas that were prepared using a RepliSet F5 silicone compound from Struers. Consequently, a methodology was developed for measuring surface roughness using the Alicona microscope based on these replicas. A 10× objective lens was used during the measurements, and the pixel size was 0.88 µm × 0.88 µm. Each time, an area of approximately 1 mm × 4 mm was measured. The lowest roughness values were observed for mSLA samples (Sa = 6.72–8.54 µm, Spk + Sk + Svk = 33.36–42.16 µm), whereas SLS exhibited the highest roughness (Sa = 27.86 µm, Spk + Sk + Svk = 183.79 µm). PJ samples exhibited intermediate roughness with significant anisotropy (Sa = 11.65 µm, Spk + Sk + Svk = 72.1 µm), which was strongly influenced by the print angle. FFF surfaces showed directional patterns and layer-dependent roughness, with the Sa parameter being the same (12.44 µm) for both PETG and PLA materials. The steepest slopes were observed for SLS surfaces (Sdq = 7.67), while mSLA exhibited the flattest microstructure (Sdq = 0.48–0.89). Statistical analysis confirmed that material type significantly influenced topography in mSLA, while print angle strongly affected PJ and FFF (although for FFF, further studies would be beneficial). The results of the research conducted can be used to develop a methodology for optimizing the printing process to achieve the required geometric surface structure.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Faculty of Mechanical Engineering and Aeronautics, Rzeszów University of Technology, 35-959 Rzeszów, Poland.
- Faculty of Mechanical Engineering, Opole University of Technology, Mikołajczyka 5 Str., 45-001 Opole, Poland.
- Faculty of Mechanical and Industrial Engineering, Warsaw University of Technology, Narbutta 85 Str., 02-524 Warsaw, Poland.
- Faculty of Automotive and Construction Machinery Engineering, Warsaw University of Technology, Narbutta 84 Str., 02-524 Warsaw, Poland.
ORCID-Profile: Anna Bazan, Paweł Turek, Grzegorz Budzik, Piotr Niesłony, Roman Grygoruk, Przemysław Siemiński
Förderung
- Minister of Science and Higher Education Republic of Poland
Zitieren
APA
Bazan, A., Turek, P., Budzik, G., Niesłony, P., Grygoruk, R., & Siemiński, P. (2025). The Influence of Model Orientation on the Surface Roughness of Polymeric Models Produced by FFF, mSLA, PJ, and SLS Methods. Materials, 18(24), 5600. https://doi.org/10.3390/ma18245600
Vancouver
Bazan A, Turek P, Budzik G, Niesłony P, Grygoruk R, Siemiński P. The Influence of Model Orientation on the Surface Roughness of Polymeric Models Produced by FFF, mSLA, PJ, and SLS Methods. Materials. 2025;18(24):5600. doi:10.3390/ma18245600
BibTeX
@article{Bazan2025,
author = {Bazan, Anna and Turek, Paweł and Budzik, Grzegorz and Niesłony, Piotr and Grygoruk, Roman and Siemiński, Przemysław},
title = {The Influence of Model Orientation on the Surface Roughness of Polymeric Models Produced by FFF, mSLA, PJ, and SLS Methods},
journal = {Materials},
year = {2025},
volume = {18},
number = {24},
pages = {5600},
doi = {10.3390/ma18245600}
}
EUVIMED