The Influence of Powder Composition and Hydrogen Consumption on the Structural, Corrosion and Tribological Characteristics of Fe-Cr-Al Coatings Obtained by Air Plasma Spraying
Materials · 29.11.2025 · 18 (23) · 5395
DOI: 10.3390/ma18235395 ↗Kurz gefasst
Fachartikel in der Zeitschrift Materials, online erschienen am 29.11.2025. Verfasst von Aidar Kengesbekov und 4 weiteren Autor:innen. Beteiligte Einrichtung: Institute of Composite Materials, Ust-Kamenogorsk 070000, Kazakhstan. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 31 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Committee of Science of the Ministry of Science and Higher Education of the Republic of Kazakhstan.
Abstract (Originalsprache)
Fe-Cr-Al coatings were obtained by air plasma spraying (APS) from 85Fe-12Cr-3Al and 68Fe-26Cr-6Al powders at two hydrogen flow rates (8 and 13 L/min), which resulted in four deposition regimes (A1, A2, B1, B2). Stainless steel 20Kh13 (equivalent to AISI 420) was used as the substrate material. The microstructure of the coatings has a typical lamellar layering with molten and semi-molten particles. When the hydrogen flow rate is increased to 13 L/min, a denser and more homogeneous structure with reduced porosity is observed. X-ray phase analysis revealed the presence of metal and oxide phases (Fe,Cr), Fe3O4, FeO, Fe2+Cr2O4, which indicates partial oxidation of particles during the spraying process and stabilization of the structure. Electrochemical tests in 3.5% NaCl solution showed that the 85Fe-12Cr-3Al coatings are characterized by a corrosion potential of Eo ≈ −0.60…−0.67 V, a corrosion current density of io = (2.6–4.7) × 10−5 A/cm2, and a corrosion rate of 0.30–0.55 mm/year, whereas the 68Fe-26Cr-6Al coatings exhibit lower values of io = (1.4–2.9) × 10−5 A/cm2 and a corrosion rate of 0.17–0.34 mm/year, indicating the formation of a denser protective oxide film (Cr2O3 + Al2O3) and enhanced surface passivation. Tribological tests showed that 85Fe-12Cr-3Al coatings demonstrate more stable friction compared to 68Fe-26Cr-6Al, while for regime B2, after 180 m, an increase in the friction coefficient is observed, caused by brittleness and the local destruction of the oxide film. A comprehensive analysis of the results showed that increasing the hydrogen consumption to 13 L/min improves the density and corrosion–tribological characteristics of the coatings.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Institute of Composite Materials, Ust-Kamenogorsk 070000, Kazakhstan.
- Research Center Surface Engineering and Tribology, Sarsen Amanzholov East Kazakhstan University, Ust-Kamenogorsk 070000, Kazakhstan.
- Metallurgical and Materials Engineering Department, Sakarya University, 54050 Sakarya, Turkey.
ORCID-Profile: Aidar Kengesbekov, Aiym Nabioldina
Förderung
- Committee of Science of the Ministry of Science and Higher Education of the Republic of Kazakhstan
Zitieren
APA
Kengesbekov, A., Buitkenov, D., Erdogan, G., Nabioldina, A., & Komekov, S. (2025). The Influence of Powder Composition and Hydrogen Consumption on the Structural, Corrosion and Tribological Characteristics of Fe-Cr-Al Coatings Obtained by Air Plasma Spraying. Materials, 18(23), 5395. https://doi.org/10.3390/ma18235395
Vancouver
Kengesbekov A, Buitkenov D, Erdogan G, Nabioldina A, Komekov S. The Influence of Powder Composition and Hydrogen Consumption on the Structural, Corrosion and Tribological Characteristics of Fe-Cr-Al Coatings Obtained by Air Plasma Spraying. Materials. 2025;18(23):5395. doi:10.3390/ma18235395
BibTeX
@article{Kengesbekov2025,
author = {Kengesbekov, Aidar and Buitkenov, Dastan and Erdogan, Garip and Nabioldina, Aiym and Komekov, Sultan},
title = {The Influence of Powder Composition and Hydrogen Consumption on the Structural, Corrosion and Tribological Characteristics of Fe-Cr-Al Coatings Obtained by Air Plasma Spraying},
journal = {Materials},
year = {2025},
volume = {18},
number = {23},
pages = {5395},
doi = {10.3390/ma18235395}
}
EUVIMED