EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Possibilities of Using 3D Printing with Polymers as Structural Components

Marcin Artur Kwapisz iD, Piotr Paszta iD, Wiktor Lacki iD

Materials · 28.11.2025 · 18 (23) · 5384

DOI: 10.3390/ma18235384 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 28.11.2025. Verfasst von Marcin Artur Kwapisz und 2 weiteren Autor:innen. Beteiligte Einrichtung: Faculty of Production Engineering and Materials Technology, Czestochowa University of Technology, Al. Armii Krajowej 19, 42-201 Częstochowa, Poland. Die Arbeit wurde bisher 2-mal zitiert (Crossref) und nennt 23 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Częstochowa University of Technology.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This article investigates the potential of using polymer-based Fused Filament Fabrication (FFF) 3D printing to manufacture structural components. This study aimed to explore the application of this technology within manufacturing processes. This research focused on material analysis, using a gear wheel from a lawn mower’s drive system as a case study. To achieve the purpose of this study, a reverse engineering process was carried out to create 2D and 3D documentation based on a physical piece. The geometric model created in the CAD environment was optimized for volume. It was intended to keep the material expenditure unchanged, which is intensified during the 3D printing process due to the need to apply an adhesive layer and supports. The final design process of the geometric model of the prototype was subjected to numerical analyses in terms of total deformation and reduced stresses for materials commonly used as filaments in the FDM/FFF 3D printing technology. The basic filaments PLA, ABS, and PA6 and PA12 were analyzed in this study. The results of the analyses showed that two of the four selected filaments had to be rejected due to significant deterioration in strength properties. Finally, the prototype workpieces were printed using materials approved for the manufacturing process.

Schlagwörter

Stichwörter der Autor:innen

3D printingABSFDM/FFFFEM analysisPA12PA6PLAincremental methodsstrength testing

Autor:innen und Institutionen

  • Faculty of Production Engineering and Materials Technology, Czestochowa University of Technology, Al. Armii Krajowej 19, 42-201 Częstochowa, Poland.
  • Faculty of Mechanical Engineering, Czestochowa University of Technology, Al. Armii Krajowej 21, 42-201 Częstochowa, Poland.

ORCID-Profile: Marcin Artur Kwapisz, Piotr Paszta, Wiktor Lacki

Förderung

  • Częstochowa University of Technology

Zitieren

APA

Kwapisz, M. A., Paszta, P., & Lacki, W. (2025). Possibilities of Using 3D Printing with Polymers as Structural Components. Materials, 18(23), 5384. https://doi.org/10.3390/ma18235384

Vancouver

Kwapisz MA, Paszta P, Lacki W. Possibilities of Using 3D Printing with Polymers as Structural Components. Materials. 2025;18(23):5384. doi:10.3390/ma18235384

BibTeX
@article{Kwapisz2025,
  author = {Kwapisz, Marcin Artur and Paszta, Piotr and Lacki, Wiktor},
  title = {Possibilities of Using 3D Printing with Polymers as Structural Components},
  journal = {Materials},
  year = {2025},
  volume = {18},
  number = {23},
  pages = {5384},
  doi = {10.3390/ma18235384}
}
Kostenlos starten →