In Vitro Degradation Studies of 3D-Printed Thermoplastic Polyurethane for the Design of Vascular Implant
Materials · 29.10.2025 · 18 (21) · 4948
DOI: 10.3390/ma18214948 ↗Kurz gefasst
Fachartikel in der Zeitschrift Materials, online erschienen am 29.10.2025. Verfasst von Kim Vanden Broeck und 7 weiteren Autor:innen. Beteiligte Einrichtung: University of Lille, INSERM, CHU Lille, U1008, F-59000 Lille, France. Die Arbeit wurde bisher 4-mal zitiert (Crossref) und nennt 53 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Métropole Européenne Lille, Lille European Metropolis.
Abstract (Originalsprache)
Three-dimensional printing has emerged as a promising technology in endovascular surgery for the production of patient-specific stent-grafts. Thermoplastic polyurethane (TPU) is widely used for this purpose due to its favourable biocompatibility, hemocompatibility, and mechanical properties. However, its long-term stability under physiological conditions remains uncertain. This study evaluates the ageing behaviour of 3D-printed TPU stent-grafts under accelerated oxidative conditions (20% H2O2–0.1 M CoCl2) over three months, corresponding to approximately 45 months in vivo, and during three months in hydrolytic (0.1 M NaOH) conditions. Mechanical, physicochemical, thermal, and surface properties were periodically analysed. Differential scanning calorimetry revealed a decrease in crystallisation enthalpy of 41% and a reduction in melting enthalpy of 29% after hydrolytic ageing, whereas no decrease was observed after oxidative ageing. Despite these chemical changes, size exclusion chromatography indicated minimal chain scission. However, spectroscopy and microscopy showed minor chain scission and additive migration (antioxidant and lubricant). Nevertheless, tensile testing highlighted that mechanical performance remained within clinically acceptable ranges. These findings demonstrate that 3D-printed TPU vascular implants retain essential properties under prolonged simulated ageing, supporting their safety and durability for vascular applications.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- University of Lille, INSERM, CHU Lille, U1008, F-59000 Lille, France.
- University of Lille, CNRS, INRAE, Centrale Lille, UMR 8207-UMET-Unité Matériaux et Transformations, F-59000 Lille, France.
- Institut Coeur Poumon, Regional Hospital Center University of Lille (CHRU Lille), 2 Avenue Oscar Lambret, F-59000 Lille, France.
ORCID-Profile: Mickaël Maton, Nicolas Tabary, Jonathan Sobocinski
Förderung
- Métropole Européenne Lille
- Lille European Metropolis
Zitieren
APA
Vanden Broeck, K., M'Bengue, M. S., Mesnard, T., Maton, M., Tabary, N., Sobocinski, J., Martel, B., & Blanchemain, N. (2025). In Vitro Degradation Studies of 3D-Printed Thermoplastic Polyurethane for the Design of Vascular Implant. Materials, 18(21), 4948. https://doi.org/10.3390/ma18214948
Vancouver
Vanden Broeck K, M'Bengue MS, Mesnard T, Maton M, Tabary N, Sobocinski J, et al. In Vitro Degradation Studies of 3D-Printed Thermoplastic Polyurethane for the Design of Vascular Implant. Materials. 2025;18(21):4948. doi:10.3390/ma18214948
BibTeX
@article{VandenBroeck2025,
author = {Vanden Broeck, Kim and M'Bengue, Marie-Stella and Mesnard, Thomas and Maton, Mickaël and Tabary, Nicolas and Sobocinski, Jonathan and Martel, Bernard and Blanchemain, Nicolas},
title = {In Vitro Degradation Studies of 3D-Printed Thermoplastic Polyurethane for the Design of Vascular Implant},
journal = {Materials},
year = {2025},
volume = {18},
number = {21},
pages = {4948},
doi = {10.3390/ma18214948}
}
EUVIMED