EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Enhancing Fatigue Lifetime of Secondary AlZn10Si8Mg Alloys Through Shot Peening: Influence of Iron Content and Surface Defects

Denisa Straková iD, Zuzana Šurdová iD, Eva Tillová iD, Lenka Kuchariková iD, Martin Mikolajčík iD, Denisa Závodská, Mario Guagliano iD

Materials · 20.08.2025 · 18 (16) · 3901

DOI: 10.3390/ma18163901 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 20.08.2025. Verfasst von Denisa Straková und 6 weiteren Autor:innen. Beteiligte Einrichtung: Department of Materials Engineering, Faculty of Mechanical Engineering, University of Zilina, Univerzitna 8215/1, 010 26 Zilina, Slovakia. Die Arbeit wurde bisher 3-mal zitiert (Crossref) und nennt 38 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Ministry of Education, Research, Development and Youth of the Slovak Republic.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The rising demand for aluminium and environmental concerns highlight the need for a circular economy using recycled alloys. This study examines the effect of shot peening on the high-cycle fatigue life of secondary AlZn10Si8Mg alloys with different iron contents: Alloy A (0.14 wt.% Fe) and Alloy B (0.56 wt.% Fe). Although both alloys showed similar tensile properties, Alloy B had higher porosity and finer β-Al5FeSi intermetallics. Shot peening was applied at 100% and 1000% coverage to evaluate changes in surface roughness, porosity, residual stresses, and fatigue performance. The treatment significantly reduced surface-connected porosity via plastic deformation, enhancing fatigue life despite increased roughness. Fatigue tests showed a 21% increase in fatigue limit for Alloy A and a 6% gain for Alloy B at higher coverage. Fractographic analysis revealed that 95% of fatigue cracks initiated at surface pores. Residual stress measurements confirmed compressive stresses were limited to the near-surface layer, with minimal influence on subsurface crack propagation. Overall, shot peening proves to be an effective method for improving fatigue resistance in recycled aluminium alloys, even in alloys with elevated iron content, reinforcing their potential for structural applications under cyclic loading.

Schlagwörter

Stichwörter der Autor:innen

AlZn10Si8Mgfatigue propertiesiron contentsecondary aluminium alloysshot peening

Autor:innen und Institutionen

  • Department of Materials Engineering, Faculty of Mechanical Engineering, University of Zilina, Univerzitna 8215/1, 010 26 Zilina, Slovakia.
  • VUTCH, Rybniky 954/10, 011 68 Zilina, Slovakia.
  • Department of Mechanical Engineering, Politecnico di Milano, 20158 Milano, Italy.

ORCID-Profile: Denisa Straková, Zuzana Šurdová, Eva Tillová, Lenka Kuchariková, Martin Mikolajčík, Mario Guagliano

Förderung

  • Ministry of Education, Research, Development and Youth of the Slovak Republic

Zitieren

APA

Straková, D., Šurdová, Z., Tillová, E., Kuchariková, L., Mikolajčík, M., Závodská, D., & Guagliano, M. (2025). Enhancing Fatigue Lifetime of Secondary AlZn10Si8Mg Alloys Through Shot Peening: Influence of Iron Content and Surface Defects. Materials, 18(16), 3901. https://doi.org/10.3390/ma18163901

Vancouver

Straková D, Šurdová Z, Tillová E, Kuchariková L, Mikolajčík M, Závodská D, et al. Enhancing Fatigue Lifetime of Secondary AlZn10Si8Mg Alloys Through Shot Peening: Influence of Iron Content and Surface Defects. Materials. 2025;18(16):3901. doi:10.3390/ma18163901

BibTeX
@article{Strakov2025,
  author = {Straková, Denisa and Šurdová, Zuzana and Tillová, Eva and Kuchariková, Lenka and Mikolajčík, Martin and Závodská, Denisa and Guagliano, Mario},
  title = {Enhancing Fatigue Lifetime of Secondary AlZn10Si8Mg Alloys Through Shot Peening: Influence of Iron Content and Surface Defects},
  journal = {Materials},
  year = {2025},
  volume = {18},
  number = {16},
  pages = {3901},
  doi = {10.3390/ma18163901}
}
Kostenlos starten →