EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Analysis of the Microstructure and Mechanical Properties of Austenitic Stainless Steel 310 Manufactured via WAAM

Aline Cipriano, Célia de Fraga Malfatti iD, Henrique Cechinel Casagrande iD, Anderson Daleffe iD, Jovani Castelan iD, Pedro Henrique Menegaro Possamai

Materials · 18.08.2025 · 18 (16) · 3855

DOI: 10.3390/ma18163855 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 18.08.2025. Verfasst von Aline Cipriano und 5 weiteren Autor:innen. Beteiligte Einrichtung: Department Metallurgical Engineering, Universidade Federal do Rio Grande do Sul (UFRGS), Porto Alegre 90010-150, Brazil. Die Arbeit wurde bisher 11-mal zitiert (Crossref) und nennt 92 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Fundação de Amparo à Pesquisa e Inovação do Estado de Santa Catarina.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The objective of this study was to characterize austenitic stainless steel 310 produced by Wire and Arc Additive Manufacturing (WAAM), addressing a gap in the literature regarding this alloy. Microstructural, chemical, and mechanical analyses were performed. Optical and electron microscopy revealed a predominantly columnar grain structure with characteristic tracks along the deposition direction. Point and mapping EDS analyses indicated a homogeneous distribution of iron, chromium, and nickel; however, point measurements suggested a possible underestimation of nickel, likely due to high relative error. Tensile tests demonstrated anisotropic mechanical behavior, with yield strength meeting standards at 45° and 90°, but lower at 0°. Ultimate tensile strength and elongation were below conventional requirements, with a maximum elongation of 15% at 90°. Additionally, the sample exhibited a total porosity of approximately 0.89%, which contributes to the reduction in mechanical properties, especially in the direction parallel to the deposition tracks. Overall, the WAAM-produced 310 stainless steel presented a microstructure similar to hot-rolled and annealed AISI 310 steel, but with distinctive features related to the additive process, such as mechanical anisotropy and microstructural directionality. These limitations highlight the need for process optimization to improve mechanical performance but reinforce the alloy’s structural potential in additive manufacturing.

Schlagwörter

Stichwörter der Autor:innen

AISI 310 austenitic stainless steelWire and Arc Additive Manufacturing (WAAM)microstructural characterizationoptical emission spectrometry (OES)tensile strength and ductility

Autor:innen und Institutionen

  • Department Metallurgical Engineering, Universidade Federal do Rio Grande do Sul (UFRGS), Porto Alegre 90010-150, Brazil.
  • Department Metallurgical Engineering, Universidade Federal de Santa Catarina (UFSC), Florianópolis 88040-900, Brazil.
  • Department Additive Manufacturing, Centro Universitário SATC (UNISATC), Criciúma 88805-380, Brazil.

ORCID-Profile: Célia de Fraga Malfatti, Henrique Cechinel Casagrande, Anderson Daleffe, Jovani Castelan

Förderung

  • Fundação de Amparo à Pesquisa e Inovação do Estado de Santa Catarina

Zitieren

APA

Cipriano, A., Malfatti, C. F., Casagrande, H. C., Daleffe, A., Castelan, J., & Possamai, P. H. M. (2025). Analysis of the Microstructure and Mechanical Properties of Austenitic Stainless Steel 310 Manufactured via WAAM. Materials, 18(16), 3855. https://doi.org/10.3390/ma18163855

Vancouver

Cipriano A, Malfatti CF, Casagrande HC, Daleffe A, Castelan J, Possamai PHM. Analysis of the Microstructure and Mechanical Properties of Austenitic Stainless Steel 310 Manufactured via WAAM. Materials. 2025;18(16):3855. doi:10.3390/ma18163855

BibTeX
@article{Cipriano2025,
  author = {Cipriano, Aline and Malfatti, Célia de Fraga and Casagrande, Henrique Cechinel and Daleffe, Anderson and Castelan, Jovani and Possamai, Pedro Henrique Menegaro},
  title = {Analysis of the Microstructure and Mechanical Properties of Austenitic Stainless Steel 310 Manufactured via WAAM},
  journal = {Materials},
  year = {2025},
  volume = {18},
  number = {16},
  pages = {3855},
  doi = {10.3390/ma18163855}
}
Kostenlos starten →