The Influence of Heat Treatment Process on the Residual Ferrite in 304L Austenitic Stainless Steel Continuous Casting Slab
Materials · 08.08.2025 · 18 (16) · 3724
DOI: 10.3390/ma18163724 ↗Kurz gefasst
Fachartikel in der Zeitschrift Materials, online erschienen am 08.08.2025. Verfasst von Zhixuan Xue und 9 weiteren Autor:innen. Beteiligte Einrichtung: College of Materials Science and Engineering, Taiyuan University of Technology, Taiyuan 030024, China. Die Arbeit wurde bisher 9-mal zitiert (Crossref) und nennt 54 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: The Applied Fundamental Research Programs of Shanxi Province, the Shanxi Scholarship Council of China, the "Chunhui Plan" Collaborative Research Project by the Ministry of Education of China.
Abstract (Originalsprache)
This study investigates the distribution characteristics of residual ferrite in 304L austenitic stainless steel continuous casting slab and the impact of heat treatment processes on its content. Through optical microscopy (OM), thermodynamic calculation software (Thermo–Calc) and heat treatment experiments, it is found that the residual ferrite content along the thickness direction at the width center of the slab exhibits an “M”-shaped distribution—lowest at the edges (approximately 3%) and highest near the center (approximately 13%). Within the triangular zone of the slab, the residual ferrite content varies between 1.8% and 12.2%, with its average along the thickness direction also showing an “M”-shaped distribution; along the width direction, the average residual ferrite content is lower at the edge positions, while within the internal triangular zone, it ranges between 8% and 10%. The ferrite morphology changes significantly across solidification zones: elongated in the surface fine-grain zone, lath-like and skeletal in the columnar grain zone and network-like in the central equiaxed grain zone. Thermodynamic calculations indicate that the solidification mode of the 304L continuous casting slab follows the FA mode. Heat treatment experiments conducted across the entire slab thickness demonstrate effective reduction in residual ferrite content; the optimal reduction is achieved at 1250 °C with a 48 min hold followed by air cooling while preserving the original “M”-shaped distribution characteristic after treatment. Increasing the heat treatment temperature, prolonging the holding time and reducing the cooling rate all contribute to reducing residual ferrite content.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- College of Materials Science and Engineering, Taiyuan University of Technology, Taiyuan 030024, China.
- College of Mechanical Engineering, Taiyuan University of Technology, Taiyuan 030024, China.
- Xinzhou Comprehensive Inspection and Testing Center, Xinzhou 034000, China.
- Department of Materials Science and Engineering, KTH Royal Institute of Technology, SE-100 44 Stockholm, Sweden.
ORCID-Profile: Chao Chen, Wangzhong Mu
Förderung
- The Applied Fundamental Research Programs of Shanxi Province
- the Shanxi Scholarship Council of China
- the "Chunhui Plan" Collaborative Research Project by the Ministry of Education of China
- The Graduate Innovation Project of Shanxi Province
- The Undergraduate Innovation and Entrepreneurship Training Program of Shanxi Province
- Applied Fundamental Research Programs of Shanxi Province
- Shanxi Scholarship Council of China
- Ministry of Education of China
Zitieren
APA
Xue, Z., Yang, K., Li, Y., Pei, C., Hou, D., Zhao, Q., Wang, Y., Chen, L., Chen, C., & Mu, W. (2025). The Influence of Heat Treatment Process on the Residual Ferrite in 304L Austenitic Stainless Steel Continuous Casting Slab. Materials, 18(16), 3724. https://doi.org/10.3390/ma18163724
Vancouver
Xue Z, Yang K, Li Y, Pei C, Hou D, Zhao Q, et al. The Influence of Heat Treatment Process on the Residual Ferrite in 304L Austenitic Stainless Steel Continuous Casting Slab. Materials. 2025;18(16):3724. doi:10.3390/ma18163724
BibTeX
@article{Xue2025,
author = {Xue, Zhixuan and Yang, Kun and Li, Yafeng and Pei, Chaochao and Hou, Dongzhi and Zhao, Qi and Wang, Yang and Chen, Lei and Chen, Chao and Mu, Wangzhong},
title = {The Influence of Heat Treatment Process on the Residual Ferrite in 304L Austenitic Stainless Steel Continuous Casting Slab},
journal = {Materials},
year = {2025},
volume = {18},
number = {16},
pages = {3724},
doi = {10.3390/ma18163724}
}
EUVIMED