EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Numerical Analysis of the Process of Drawing Thin-Walled CuSn8 Alloy Tubes on a Cylindrical Plug

Maciej Suliga, Sebastian Mróz iD, Piotr Szota iD, Mateusz Wasilewski, Konrad Jaroszewski

Materials · 12.06.2025 · 18 (12) · 2754

DOI: 10.3390/ma18122754 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 12.06.2025. Verfasst von Maciej Suliga und 4 weiteren Autor:innen. Beteiligte Einrichtung: Faculty of Production Engineering and Materials Technology, Czestochowa University of Technology, Armii Krajowej 19, 42-201 Czestochowa, Poland. Die Arbeit wurde bisher 3-mal zitiert (Crossref) und nennt 32 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The paper presents the results of FEM computer simulations of the drawing process on a cylindrical journal of thin-walled CuSn8 alloy tubes. This study demonstrates through FEM simulations that the drawing angle significantly affects the state of stress, strain and tool wear. Regardless of the geometry of the drawing die, greater wear was noted for the cylindrical plug. Increasing the angle of drawing die 2α from 6° to 38° contributed to a slight 5% increase in wear of the drawing dies and more than 80% increase in plug wear. Accelerated tool wear at high angles is to be associated with higher pipe pressures on the drawing die and plug. Inadequate selection of drawing geometry can cause additional material deformation effort and material fracture in the industrial drawing process of thin-walled tubes. After the drawing process, these tubes may also show non-uniform wall thickness. The optimum drawing angle for thin-walled tubes is 2α = 22°, for which about a 10% decrease in the drawing force was recorded.

Schlagwörter

Stichwörter der Autor:innen

FEMbronzedie geometrystress and strain statetemperaturetube drawing processwear

Autor:innen und Institutionen

  • Faculty of Production Engineering and Materials Technology, Czestochowa University of Technology, Armii Krajowej 19, 42-201 Czestochowa, Poland.
  • WIKA Polska SGF, Kawka 6, 87-800 Włocławek, Poland.

ORCID-Profile: Sebastian Mróz, Piotr Szota

Zitieren

APA

Suliga, M., Mróz, S., Szota, P., Wasilewski, M., & Jaroszewski, K. (2025). Numerical Analysis of the Process of Drawing Thin-Walled CuSn8 Alloy Tubes on a Cylindrical Plug. Materials, 18(12), 2754. https://doi.org/10.3390/ma18122754

Vancouver

Suliga M, Mróz S, Szota P, Wasilewski M, Jaroszewski K. Numerical Analysis of the Process of Drawing Thin-Walled CuSn8 Alloy Tubes on a Cylindrical Plug. Materials. 2025;18(12):2754. doi:10.3390/ma18122754

BibTeX
@article{Suliga2025,
  author = {Suliga, Maciej and Mróz, Sebastian and Szota, Piotr and Wasilewski, Mateusz and Jaroszewski, Konrad},
  title = {Numerical Analysis of the Process of Drawing Thin-Walled CuSn8 Alloy Tubes on a Cylindrical Plug},
  journal = {Materials},
  year = {2025},
  volume = {18},
  number = {12},
  pages = {2754},
  doi = {10.3390/ma18122754}
}
Kostenlos starten →