EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Cold Drawing of AISI 321 Stainless Steel Thin-Walled Seamless Tubes on a Floating Plug

Krzysztof Żaba iD, Tomasz Trzepieciński iD

Materials · 18.08.2023 · 16 (16) · 5684

DOI: 10.3390/ma16165684 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 18.08.2023. Verfasst von Krzysztof Żaba und 1 weiteren Autor:innen. Beteiligte Einrichtung: Department of Metal Working and Physical Metallurgy of Non-Ferrous Metals, Faculty of Non-Ferrous Metals, AGH-University of Science and Technology, a…. Die Arbeit wurde bisher 4-mal zitiert (Crossref) und nennt 35 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The paper presents the results of an analysis of the process of drawing AISI 321 stainless steel thin-walled seamless tubes on a floating plug. The influence of the geometry of dies and plugs, drawing velocity, and lubricants on the possibility of carrying out the pipe drawing process without a loss of strength of the lubricating film and, consequently, disturbance of the forming process and tube cracking, and also on the temperature in the drawing process, the mechanical properties of the tubes drawn, and the microhardness and roughness of the inner and outer surface of the tubes was investigated. The parameters of the drawing tools used were as follows: angle of drawing dies α = 16° and floating plugs with angles of inclination of the conical part of the plug β = 11.5°, 13°, and 14°. The drawing dies and floating plugs were made of G10 sintered carbide. Drawing speed was varied over the range 1 to 10 m/min. The study used several lubricants. Tubes with dimensions (outer diameter D0, wall thickness g0 before drawing process) D0 = 19 mm, g0 = 1.2 mm and D0 = 18 mm, g0 = 1.2 mm were drawn to produce tubes with dimensions (outer diameter Dk, wall thickness gk after drawing process) Dk = 16 mm, gk = 1.06 mm on a drawbench with the same total elongation, while the diameter and wall thickness were changed. During the process, continuous measurements were made of the drawing force and temperature in the deformation zone and on the tube surface. It was found that the drawing process causes a decrease in the roughness parameters Ra and Rz of the inner surface of the tubes. Moreover, after drawing, an increase of 30–70% was observed in the microhardness of the tube material in relation to the microhardness of the charge material. Based on the test results, it can be concluded that the work of frictional forces is the main direction of optimization of tube drawing on a floating plug process of hard-deforming materials.

Schlagwörter

Stichwörter der Autor:innen

AISI 321 stainless steelcold tube drawingfloating pluglubricantsmechanical propertiesmicrohardness

Autor:innen und Institutionen

  • Department of Metal Working and Physical Metallurgy of Non-Ferrous Metals, Faculty of Non-Ferrous Metals, AGH-University of Science and Technology, al. Adama Mickiewicza 30, 30-059 Cracow, Poland.
  • Department of Manufacturing Processes and Production Engineering, Faculty of Mechanical Engineering and Aeronautics, Rzeszow University of Technology, al. Powst. Warszawy 8, 35-959 Rzeszów, Poland.

ORCID-Profile: Krzysztof Żaba, Tomasz Trzepieciński

Zitieren

APA

Żaba, K., & Trzepieciński, T. (2023). Cold Drawing of AISI 321 Stainless Steel Thin-Walled Seamless Tubes on a Floating Plug. Materials, 16(16), 5684. https://doi.org/10.3390/ma16165684

Vancouver

Żaba K, Trzepieciński T. Cold Drawing of AISI 321 Stainless Steel Thin-Walled Seamless Tubes on a Floating Plug. Materials. 2023;16(16):5684. doi:10.3390/ma16165684

BibTeX
@article{aba2023,
  author = {Żaba, Krzysztof and Trzepieciński, Tomasz},
  title = {Cold Drawing of AISI 321 Stainless Steel Thin-Walled Seamless Tubes on a Floating Plug},
  journal = {Materials},
  year = {2023},
  volume = {16},
  number = {16},
  pages = {5684},
  doi = {10.3390/ma16165684}
}
Kostenlos starten →