EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Effects of Pretreatment Processes on Grain Size and Wear Resistance of Laser-Induction Hybrid Phase Transformation Hardened Layer of 42CrMo Steel

Qunli Zhang iD, Peng Shen, Zhijun Chen, Guolong Wu, Zhuguo Li, Wenjian Wang, Jianhua Yao

Materials · 07.06.2025 · 18 (12) · 2695

DOI: 10.3390/ma18122695 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 07.06.2025. Verfasst von Qunli Zhang und 6 weiteren Autor:innen. Beteiligte Einrichtung: College of Mechanical Engineering, Zhejiang University of Technology, Hangzhou 310014, China. Die Arbeit wurde bisher 4-mal zitiert (Crossref) und nennt 36 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: National Key Research and Development Program of China, "Elite" Program of Zhejiang Province, Zhejiang Provincial Special Support Plan for High-Level Talents.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

To address the issue of surface grain coarsening in laser-induction hybrid phase transformation of 42CrMo steel, this study investigated the effects of four pretreatment processes (quenching–tempering (QT), laser-induction quenching (LIQ), laser-induction normalizing (LIN), and laser-induction annealing (LIA)) on the austenite grain size and wear resistance after laser-induction hybrid phase transformation. The results showed that QT resulted in a tempered sorbite structure, resulting in coarse austenite grains (139.8 μm) due to sparse nucleation sites. LIQ generated lath martensite, and its high dislocation density and large-angle grain boundaries led to even larger grains (145.5 μm). In contrast, LIN and LIA formed bainite and granular pearlite, respectively, which refined austenite grains (78.8 μm and 75.5 μm) through dense nucleation and grain boundary pinning. After laser-induction hybrid phase transformation, all specimens achieved hardened layer depths exceeding 6.9 mm. When the pretreatment was LIN or LIA, the specimens after laser-induction hybrid phase transformation exhibited surface microhardness values of 760.3 HV0.3 and 765.2 HV0.3, respectively, which were 12 to 15% higher than those of the QT- and LIQ-pretreated specimens, primarily due to fine-grain strengthening. The friction coefficient decreased from 0.52 in specimens pretreated by QT and LIQ to 0.45 in those pretreated by LIN and LIA, representing a reduction of approximately 20%. The results confirm that regulating the initial microstructure via pretreatment effectively inhibits austenite grain coarsening, thereby enhancing the microhardness and wear resistance after transformation.

Schlagwörter

Stichwörter der Autor:innen

42CrMo steelaustenite grainlaser-induction hybrid phase transformationpretreatment processwear-resistant properties

Autor:innen und Institutionen

  • College of Mechanical Engineering, Zhejiang University of Technology, Hangzhou 310014, China.
  • Institute of Laser Advanced Manufacturing, Zhejiang University of Technology, Hangzhou 310014, China.
  • Zhejiang Provincial Innovation Center for Laser Intelligent Equipment Technology, Wenzhou 325000, China.
  • College of Materials Science and Engineering, Shanghai Jiao Tong University, Shanghai 200240, China.
  • College of Mechanical Engineering, Southwest Jiaotong University, Chengdu 611756, China.

ORCID-Profile: Qunli Zhang

Förderung

  • National Key Research and Development Program of China
  • "Elite" Program of Zhejiang Province
  • Zhejiang Provincial Special Support Plan for High-Level Talents
  • “Elite” Program of Zhejiang Province

Zitieren

APA

Zhang, Q., Shen, P., Chen, Z., Wu, G., Li, Z., Wang, W., & Yao, J. (2025). Effects of Pretreatment Processes on Grain Size and Wear Resistance of Laser-Induction Hybrid Phase Transformation Hardened Layer of 42CrMo Steel. Materials, 18(12), 2695. https://doi.org/10.3390/ma18122695

Vancouver

Zhang Q, Shen P, Chen Z, Wu G, Li Z, Wang W, et al. Effects of Pretreatment Processes on Grain Size and Wear Resistance of Laser-Induction Hybrid Phase Transformation Hardened Layer of 42CrMo Steel. Materials. 2025;18(12):2695. doi:10.3390/ma18122695

BibTeX
@article{Zhang2025,
  author = {Zhang, Qunli and Shen, Peng and Chen, Zhijun and Wu, Guolong and Li, Zhuguo and Wang, Wenjian and Yao, Jianhua},
  title = {Effects of Pretreatment Processes on Grain Size and Wear Resistance of Laser-Induction Hybrid Phase Transformation Hardened Layer of 42CrMo Steel},
  journal = {Materials},
  year = {2025},
  volume = {18},
  number = {12},
  pages = {2695},
  doi = {10.3390/ma18122695}
}
Kostenlos starten →