Tailoring Microstructure and Properties of W-Mo-Cu Composites Fabricated via Infiltration Sintering: Effects of Graphene Addition and Skeleton Relative Density
Materials · 28.05.2025 · 18 (11) · 2539
DOI: 10.3390/ma18112539 ↗Kurz gefasst
Fachartikel in der Zeitschrift Materials, online erschienen am 28.05.2025. Verfasst von Jinwen Cai und 3 weiteren Autor:innen. Beteiligte Einrichtung: School of Mechanical Engineering, Sichuan University, Chengdu 610065, China. Die Arbeit wurde bisher 3-mal zitiert (Crossref) und nennt 37 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: National Natural Science Foundation of China, Natural Science Foundation Project of Chongqing, Chongqing Postdoctoral Research Project.
Abstract (Originalsprache)
W-Mo-Cu composites show promise for advanced applications, but their properties require optimization. In this study, a novel approach utilizing Cu-coated graphene (Cu@Gr) reinforcement with skeleton relative density adjustment was employed to tailor the microstructure and properties of W-Mo-Cu composites fabricated via infiltration sintering (1300 °C, 1.5 h). The results revealed that Cu@Gr significantly promoted sintering densification, modified the phase composition, and enhanced the properties of the composite. Specifically, the addition of 0.4 wt.% Cu@Gr resulted in a relative density of 98% for the composite, representing an 8% increase compared to the material without Cu@Gr. Furthermore, when higher amounts of Cu@Gr were incorporated, the composite consistently exhibited a high degree of densification. In addition to the primary W, Mo, and Cu phases, molybdenum carbide, Mo2C, was formed at 0.4 wt.% Cu@Gr, with its content rising proportionally to graphene dosage. Notably, the composite containing 0.6 wt.% Cu@Gr exhibits the highest thermal conductivity and electrical conductivity, showing 64% and 73% increases, respectively, versus Cu@Gr-free samples. Additionally, although W-Mo green compact density variations (73–85%) did not compromise graphene-induced densification, a higher green compact density reduced the thermal/electrical conductivities but increased the hardness. These findings demonstrate that controlled Cu@Gr incorporation and green compact optimization synergistically improve the properties of W-Mo-Cu composites, providing insights into high-performance material design.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- School of Mechanical Engineering, Sichuan University, Chengdu 610065, China.
- College of Materials Science and Engineering, Chongqing University, Chongqing 400044, China.
ORCID-Profile: Keqin Feng, Hongling Zhou
Förderung
- National Natural Science Foundation of China
- Natural Science Foundation Project of Chongqing
- Chongqing Postdoctoral Research Project
Zitieren
APA
Cai, J., Jiang, Q., Feng, K., & Zhou, H. (2025). Tailoring Microstructure and Properties of W-Mo-Cu Composites Fabricated via Infiltration Sintering: Effects of Graphene Addition and Skeleton Relative Density. Materials, 18(11), 2539. https://doi.org/10.3390/ma18112539
Vancouver
Cai J, Jiang Q, Feng K, Zhou H. Tailoring Microstructure and Properties of W-Mo-Cu Composites Fabricated via Infiltration Sintering: Effects of Graphene Addition and Skeleton Relative Density. Materials. 2025;18(11):2539. doi:10.3390/ma18112539
BibTeX
@article{Cai2025,
author = {Cai, Jinwen and Jiang, Qiaoling and Feng, Keqin and Zhou, Hongling},
title = {Tailoring Microstructure and Properties of W-Mo-Cu Composites Fabricated via Infiltration Sintering: Effects of Graphene Addition and Skeleton Relative Density},
journal = {Materials},
year = {2025},
volume = {18},
number = {11},
pages = {2539},
doi = {10.3390/ma18112539}
}
EUVIMED