Improved Thin-Kerf Processing in Cf/SiC Composite by Waterjet-Guided Nanosecond Laser Decreases Oxidation and Thermal Effect
Materials · 29.03.2025 · 18 (7) · 1560
DOI: 10.3390/ma18071560 ↗Kurz gefasst
Fachartikel in der Zeitschrift Materials, online erschienen am 29.03.2025. Verfasst von Jiayu Wang und 8 weiteren Autor:innen. Beteiligte Einrichtung: Key Laboratory of Aero Engine Extreme Manufacturing Technology of Zhejiang Province, Ningbo Institute of Materials Technology and Engineering, Chines…. Die Arbeit wurde bisher 15-mal zitiert (Crossref) und nennt 56 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Shenzhen Basic Research Project, IER foundation, National Natural Science Foundation of China.
Abstract (Originalsprache)
As a hard and brittle material, the processing of Cf/SiC ceramic matrix composites (CMCs) faces significant challenges, especially in the processing of small-sized shapes. To address this challenge, laser processing with gas-assisted nanosecond laser (GNL) and waterjet-guided nanosecond laser (WNL) modes were applied to fabricate thin kerfs in the Cf/SiC composite. The surface morphology, microstructure, and chemical composition of the processed Cf/SiC composite were investigated comparatively. The results revealed that the coupling of helium in the GNL mode laser processing could make full use of the laser energy, but resulted in spattering in the kerf margin and a recast layer in the kerf surface, accompanied by obvious oxidation, while the coupling of the waterjet in the WNL mode laser processing decreased the oxidation significantly and removed the remelting debris, which produced a clear and flat kerf surface. Due to the taper caused by laser energy dissipation, the single-path laser processing in the Cf/SiC composite had a limited depth. The maximum depth of the kerf prepared by single-path laser processing with the GNL mode was about 328 μm, while that with the WNL mode was about 302 μm. The multi-path laser processing with the GNL and WNL modes could fabricate a through kerf in the Cf/SiC composite, but the coupling medium obviously influenced the surface morphology and microstructure of the underlying region. The kerf surface prepared by the GNL mode had a varied surface morphology, which transited from the top layer, covered with oxide particles and some cracks, to the bottom layer, featured with micro-grooves and small oxides. The kerf surface prepared by the WNL mode had a consistently smooth and clean morphology featured with broken carbon fiber and residual SiC matrix. The slow laser energy dissipation and open environment in the GNL mode resulted in a bigger HAZ and relatively serious oxidation, which caused local phase transformation and microstructure degradation. The isolation condition and rapid cooling in the WNL mode decreased the HAZ and restrained the oxidation, almost keeping the original microstructure. The thicknesses of the HAZ in the GNL- and WNL-processed Cf/SiC composite were about 200 μm and 100 μm, respectively. The WNL-processed Cf/SiC composite had a lower oxidation and thermal damage surface, which is instructive for the processing of the Cf/SiC composite.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Key Laboratory of Aero Engine Extreme Manufacturing Technology of Zhejiang Province, Ningbo Institute of Materials Technology and Engineering, Chinese Academy of Sciences, Ningbo 315201, China.
- Faculty of Mechanical Engineering and Mechanics, Ningbo University, Ningbo 315211, China.
- University of Chinese Academy of Sciences, Beijing 100049, China.
- PKU-HKUST ShenZhen-HongKong Institution, Shenzhen 518057, China.
- School of Mechanical Science and Engineering, Huazhong University of Science and Technology, Wuhan 430074, China.
- Shenzhen Institute, Peking University, Shenzhen 518057, China.
ORCID-Profile: Guangyi Zhang, Qiaoli Wang, Youmin Rong, Liyuan Sheng
Förderung
- Shenzhen Basic Research Project
- IER foundation
- National Natural Science Foundation of China
- Natural Science Foundation of Zhejiang Province
- Open Subject of State Key Laboratory of Intelligent Manufacturing Equipment and Technology
- Ningbo Young Science and Technology Innovation Leaders Project
- Shenzhen Basic Research Projects
Zitieren
APA
Wang, J., Zhang, G., Wang, Q., Rong, Y., Zhao, C., Chen, C., Bao, B., Zhang, W., & Sheng, L. (2025). Improved Thin-Kerf Processing in Cf/SiC Composite by Waterjet-Guided Nanosecond Laser Decreases Oxidation and Thermal Effect. Materials, 18(7), 1560. https://doi.org/10.3390/ma18071560
Vancouver
Wang J, Zhang G, Wang Q, Rong Y, Zhao C, Chen C, et al. Improved Thin-Kerf Processing in Cf/SiC Composite by Waterjet-Guided Nanosecond Laser Decreases Oxidation and Thermal Effect. Materials. 2025;18(7):1560. doi:10.3390/ma18071560
BibTeX
@article{Wang2025,
author = {Wang, Jiayu and Zhang, Guangyi and Wang, Qiaoli and Rong, Youmin and Zhao, Chaochao and Chen, Chunguang and Bao, Binying and Zhang, Wenwu and Sheng, Liyuan},
title = {Improved Thin-Kerf Processing in Cf/SiC Composite by Waterjet-Guided Nanosecond Laser Decreases Oxidation and Thermal Effect},
journal = {Materials},
year = {2025},
volume = {18},
number = {7},
pages = {1560},
doi = {10.3390/ma18071560}
}
EUVIMED