EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Cavitation Erosion of Protective Coating Based on Cordierite Filler and Epoxy Matrix

Marko Pavlović iD, Marina Dojčinović iD, Jasmina Nikolić iD, Stanko Aleksić iD, Nedeljko Tucović, Zoran Čeganjac, Saša Drmanić iD

Materials · 26.02.2025 · 18 (5) · 1034

DOI: 10.3390/ma18051034 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 26.02.2025. Verfasst von Marko Pavlović und 6 weiteren Autor:innen. Beteiligte Einrichtung: Innovation Centre of Faculty of Mechanical Engineering, University of Belgrade, 11000 Belgrade, Serbia. Die Arbeit wurde bisher 3-mal zitiert (Crossref) und nennt 44 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Ministry of Education, Science and Technological Development of the Republic of Serbia.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The goal of this study is to investigate the surface morphology changes induced by the cavitation erosion of a coating based on cordierite with an epoxy matrix for an aluminum substrate. The literature review shows a certain lack of knowledge regarding the coating’s resistance to wearing induced by water flow, which is a highly important property of the material immersed in or in contact with water streams. The main idea behind the investigation is that such a protective coating will also improve the cavitation erosion resistance of metal substrates. The protective coatings were based on cordierite filler (88 wt.%) and epoxy resin (7 wt.%). The filler, made of a mixture of kaolin, alumina, and talc, is obtained by a sintering procedure that took place at 1350 °C. X-ray diffraction analysis and scanning electron microscopy were employed in the characterization of the produced filler. The adherence of the obtained epoxy-based protective coating and resistance to water flow were tested by the ultrasonic vibration method (i.e., cavitation erosion testing). Scanning electron microscopy was used for analysis of the coating’s morphology upon cavitation erosion. Based on the value of the cavitation erosion rate and the analyzed final surface damage, it was assessed that the investigated protective coating is resistant to cavitation erosion.

Schlagwörter

Stichwörter der Autor:innen

cavitation resistancecordierite fillermetal substratemicrostructure

Autor:innen und Institutionen

  • Innovation Centre of Faculty of Mechanical Engineering, University of Belgrade, 11000 Belgrade, Serbia.
  • Faculty of Technology and Metallurgy, University of Belgrade, 11000 Belgrade, Serbia.
  • Laboratory of Physics and Chemistry, Institute of Nuclear Science INS Vinca, 11000 Belgrade, Serbia.
  • Jugoinspect A.D., 11000 Belgrade, Serbia.
  • Department in Arandelovac, Academy of Professional Studies Sumadija, 34300 Arandelovac, Serbia.

ORCID-Profile: Marko Pavlović, Marina Dojčinović, Jasmina Nikolić, Stanko Aleksić, Saša Drmanić

Förderung

  • Ministry of Education, Science and Technological Development of the Republic of Serbia

Zitieren

APA

Pavlović, M., Dojčinović, M., Nikolić, J., Aleksić, S., Tucović, N., Čeganjac, Z., & Drmanić, S. (2025). Cavitation Erosion of Protective Coating Based on Cordierite Filler and Epoxy Matrix. Materials, 18(5), 1034. https://doi.org/10.3390/ma18051034

Vancouver

Pavlović M, Dojčinović M, Nikolić J, Aleksić S, Tucović N, Čeganjac Z, et al. Cavitation Erosion of Protective Coating Based on Cordierite Filler and Epoxy Matrix. Materials. 2025;18(5):1034. doi:10.3390/ma18051034

BibTeX
@article{Pavlovi2025,
  author = {Pavlović, Marko and Dojčinović, Marina and Nikolić, Jasmina and Aleksić, Stanko and Tucović, Nedeljko and Čeganjac, Zoran and Drmanić, Saša},
  title = {Cavitation Erosion of Protective Coating Based on Cordierite Filler and Epoxy Matrix},
  journal = {Materials},
  year = {2025},
  volume = {18},
  number = {5},
  pages = {1034},
  doi = {10.3390/ma18051034}
}
Kostenlos starten →