EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Impact of Yttrium Oxide on the Synthesis and Sintering Properties of Cordierite–Mullite Composite Ceramics

Hui Zhang iD, Lu Feng, Weibo Mao, Quanming Liu, Liang Zhao, Hong Zhang

Materials · 04.02.2025 · 18 (3) · 687

DOI: 10.3390/ma18030687 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 04.02.2025. Verfasst von Hui Zhang und 5 weiteren Autor:innen. Beteiligte Einrichtung: College of Civil Engineering, Xi'an University of Architecture and Technology Hua Qing College, Xi'an 710043, China. Die Arbeit wurde bisher 15-mal zitiert (Crossref) und nennt 33 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: the Youth Fund of the National Natural Science Foundation of China, the Natural Science Foundation of Chongqing, Shaanxi Provincial Department of Education special research project.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

To enhance the mechanical properties and high-temperature performance of cordierite–mullite composite ceramics, yttrium oxide (Y2O3), a rare earth metal oxide, was employed as a sintering aid to fabricate these composites via in situ synthesis and non-pressure sintering. This study systematically investigated the formation mechanisms of the cordierite and mullite phases and examined the effects of yttrium oxide on the densification behavior, mechanical properties, volumetric stability, and thermal shock resistance. The results indicate that incorporating yttrium oxide (1.5–6.0 wt%) not only promoted the formation of the cordierite phase but also refined the microstructure and enhanced the thermal shock stability at a sintering temperature of 1350 °C. An optimal addition of 3 wt% yttrium oxide ensures that the primary phases are cordierite and mullite, with a microstructure characterized by uniformly distributed micropores, hexagonal short-columnar cordierite, and interlocking rod-like mullite, thereby significantly improving both the mechanical properties and thermal shock stability. Specifically, the room-temperature compressive strength increased by 121%, the flexural strength increased by 177%, and, after three thermal shock cycles at 1100 °C, the retention rates for compressive and flexural strengths were 87.66% and 71.01%, respectively. This research provides a critical foundation for enhancing the mechanical properties and high-temperature service performance of cordierite–mullite saggers used in lithium battery cathode materials.

Schlagwörter

Stichwörter der Autor:innen

cordierite–mullitemicrostructuresintering aidthermal shock stabilityyttrium oxide

Autor:innen und Institutionen

  • College of Civil Engineering, Xi'an University of Architecture and Technology Hua Qing College, Xi'an 710043, China.
  • Gas Turbine Technology Department, Xi'an Thermal Power Research Institute Co., Ltd., Xi'an 710032, China.
  • School of Civil Engineering and Architecture, Yangtze Normal University, Chongqing 408100, China.

ORCID-Profile: Hui Zhang

Förderung

  • the Youth Fund of the National Natural Science Foundation of China
  • the Natural Science Foundation of Chongqing
  • Shaanxi Provincial Department of Education special research project

Zitieren

APA

Zhang, H., Feng, L., Mao, W., Liu, Q., Zhao, L., & Zhang, H. (2025). Impact of Yttrium Oxide on the Synthesis and Sintering Properties of Cordierite–Mullite Composite Ceramics. Materials, 18(3), 687. https://doi.org/10.3390/ma18030687

Vancouver

Zhang H, Feng L, Mao W, Liu Q, Zhao L, Zhang H. Impact of Yttrium Oxide on the Synthesis and Sintering Properties of Cordierite–Mullite Composite Ceramics. Materials. 2025;18(3):687. doi:10.3390/ma18030687

BibTeX
@article{Zhang2025,
  author = {Zhang, Hui and Feng, Lu and Mao, Weibo and Liu, Quanming and Zhao, Liang and Zhang, Hong},
  title = {Impact of Yttrium Oxide on the Synthesis and Sintering Properties of Cordierite–Mullite Composite Ceramics},
  journal = {Materials},
  year = {2025},
  volume = {18},
  number = {3},
  pages = {687},
  doi = {10.3390/ma18030687}
}
Kostenlos starten →