Considering the Bottom Edge Cutting Effect of the Carbon Fiber Reinforced Polymer Milling Force Prediction Model and Optimization of Machining Parameters
Materials · 28.11.2024 · 17 (23) · 5844
DOI: 10.3390/ma17235844 ↗Kurz gefasst
Fachartikel in der Zeitschrift Materials, online erschienen am 28.11.2024. Verfasst von Yiwei Zhang und 4 weiteren Autor:innen. Beteiligte Einrichtung: Chongqing Engineering Research Center for Advanced Intelligent Manufacturing Technology, Chongqing Three Gorges University, Chongqing 404000, China. Die Arbeit wurde bisher 11-mal zitiert (Crossref) und nennt 35 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: the Chongqing graduate research innovation project, the Science and Technology Research Project of the Chongqing Education Commission, the College Students' Innovative Entrepreneurial Training Plan Program.
Abstract (Originalsprache)
The milling force plays a pivotal role in CFRP milling. Modeling of the milling force is helpful to explore the changing law, optimize the processing parameters, and then reduce the appearance of defects. However, most of the existing models ignore the effect of the bottom edge. In this paper, the prediction of milling force in CFRP milling processes is taken as the research object. By analyzing the milling mechanism and considering the end milling cutter’s bottom cutting edge, the prediction model of milling force was established. Based on the experimental data and simulation data of milling force, the milling force coefficient was obtained by inverse calculation. Subsequently, the predicted cutting force was compared with the experimental cutting force, showing a maximum error of 14.5%, which is within a reasonable range, and the correctness of the model was verified. Furthermore, combined with the delamination damage and the milling force prediction model, a multi-objective optimization model of milling parameters was established, and the genetic algorithm was used to solve the model. The unidirectional carbon fiber plate with a fiber direction angle of 45° was selected as the optimization example. The minimum delamination damage was obtained under the cutting conditions of a spindle speed of 4903.1569 r/min, feed rate per tooth of 0.01 mm/z, and an axial depth of cut of 0.5 mm, and the experimental verification was carried out. The feasibility of the genetic algorithm in CFRP milling parameter optimization modeling was also verified.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Chongqing Engineering Research Center for Advanced Intelligent Manufacturing Technology, Chongqing Three Gorges University, Chongqing 404000, China.
- Chongqing Engineering Technology Research Center for Light Alloy and Processing, Chongqing Three Gorges University, Chongqing 404000, China.
- School of Mechatronic Engineering, Southwest Petroleum University, Chengdu 610500, China.
Förderung
- the Chongqing graduate research innovation project
- the Science and Technology Research Project of the Chongqing Education Commission
- the College Students' Innovative Entrepreneurial Training Plan Program
- Chongqing Graduate Research Innovation Project
- Science and Technology Research Project of the Chongqing Education Commission
- College Students’ Innovative Entrepreneurial Training Plan Program
Zitieren
APA
Zhang, Y., Yan, M., Lai, Y., Wang, G., & Yang, Y. (2024). Considering the Bottom Edge Cutting Effect of the Carbon Fiber Reinforced Polymer Milling Force Prediction Model and Optimization of Machining Parameters. Materials, 17(23), 5844. https://doi.org/10.3390/ma17235844
Vancouver
Zhang Y, Yan M, Lai Y, Wang G, Yang Y. Considering the Bottom Edge Cutting Effect of the Carbon Fiber Reinforced Polymer Milling Force Prediction Model and Optimization of Machining Parameters. Materials. 2024;17(23):5844. doi:10.3390/ma17235844
BibTeX
@article{Zhang2024,
author = {Zhang, Yiwei and Yan, Mengke and Lai, Yushu and Wang, Guixing and Yang, Yifan},
title = {Considering the Bottom Edge Cutting Effect of the Carbon Fiber Reinforced Polymer Milling Force Prediction Model and Optimization of Machining Parameters},
journal = {Materials},
year = {2024},
volume = {17},
number = {23},
pages = {5844},
doi = {10.3390/ma17235844}
}
EUVIMED