Notch Effect in Acrylonitrile Styrene Acrylate (ASA) Single-Edge-Notch Bending Specimens Manufactured by Fused Filament Fabrication
Materials · 25.10.2024 · 17 (21) · 5207
DOI: 10.3390/ma17215207 ↗Kurz gefasst
Fachartikel in der Zeitschrift Materials, online erschienen am 25.10.2024. Verfasst von Sergio Cicero und 4 weiteren Autor:innen. Beteiligte Einrichtung: Laboratory of Materials Science and Engineering (LADICIM), Departamento de Ciencia e Ingeniería del Terreno y de los Materiales, University of Cantab…. Die Arbeit wurde bisher 14-mal zitiert (Crossref) und nennt 54 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Ministerio de Ciencia, Innovación y Universidades, MCIN/AEI/10.13039/501100011033/FEDER “Una manera de hacer Europa”.
Abstract (Originalsprache)
This paper analyses the notch effect in the fracture behaviour of acrylonitrile–styrene–acrylate (ASA) material manufactured by fused filament fabrication (FFF). The research is performed on 72 single-edge-notch bending (SENB) specimens containing U-notches with nominal notch radii varying from 0 mm (crack-like defects) up to 2.0 mm, and fabricated with three different raster orientations (0/90, 45/−45, 30/−60). Apparent fracture toughness values are obtained for the different conditions and the resulting notch effect is analysed through the Theory of Critical Distances. A fractographic analysis is also performed using Scanning Electron Microscopy (SEM) in order to justify the fracture (macroscopic) behaviour from the observed fracture micromechanisms. The notch effect observed in the three ASA raster orientations is very similar, and lower than that observed in other FFF polymeric alternatives (ABS, PLA).
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Laboratory of Materials Science and Engineering (LADICIM), Departamento de Ciencia e Ingeniería del Terreno y de los Materiales, University of Cantabria, Avenida de los Castros, 44, 39005 Santander, Spain.
- Department of Mechanical, Mathematics and Management (DMMM), Polytechnical University of Bari, 70126 Bari, Italy.
- Department of Sciences, Technologies and Society, University School for Advanced Studies Pavia IUSS, 27100 Pavia, Italy.
- TECNALIA, Basque Research and Technology Alliance (BRTA), Mikeletegi Pasealekua 2, 20009 Donostia-San Sebastián, Spain.
- Departamento de Ingeniería Geografica y Tecnicas de Expresion Grafica, Escuela Técnica Superior de Ingenieros de Caminos, Canales y Puertos, Universidad de Cantabria, Avenida de los Castros, 44, 39005 Santander, Spain.
ORCID-Profile: Sergio Cicero, Fabrizia Devito, Marcos Sánchez, Sergio Arrieta, Borja Arroyo
Förderung
- Ministerio de Ciencia, Innovación y Universidades
- MCIN/AEI/10.13039/501100011033/FEDER “Una manera de hacer Europa”
Zitieren
APA
Cicero, S., Devito, F., Sánchez, M., Arrieta, S., & Arroyo, B. (2024). Notch Effect in Acrylonitrile Styrene Acrylate (ASA) Single-Edge-Notch Bending Specimens Manufactured by Fused Filament Fabrication. Materials, 17(21), 5207. https://doi.org/10.3390/ma17215207
Vancouver
Cicero S, Devito F, Sánchez M, Arrieta S, Arroyo B. Notch Effect in Acrylonitrile Styrene Acrylate (ASA) Single-Edge-Notch Bending Specimens Manufactured by Fused Filament Fabrication. Materials. 2024;17(21):5207. doi:10.3390/ma17215207
BibTeX
@article{Cicero2024,
author = {Cicero, Sergio and Devito, Fabrizia and Sánchez, Marcos and Arrieta, Sergio and Arroyo, Borja},
title = {Notch Effect in Acrylonitrile Styrene Acrylate (ASA) Single-Edge-Notch Bending Specimens Manufactured by Fused Filament Fabrication},
journal = {Materials},
year = {2024},
volume = {17},
number = {21},
pages = {5207},
doi = {10.3390/ma17215207}
}
EUVIMED