EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Optimal Geometry for Focused Ion Beam-Milled Samples for Direct-Pull Micro-Tensile Testing Performed In Situ in a Scanning Electron Microscope

Daniel B Yin iD, Haiping Sun iD, Amit Misra iD

Materials · 22.10.2024 · 17 (21) · 5144

DOI: 10.3390/ma17215144 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 22.10.2024. Verfasst von Daniel B Yin und 2 weiteren Autor:innen. Beteiligte Einrichtung: Department of Materials Science and Engineering, University of Michigan, Ann Arbor, MI 48109, USA. Die Arbeit wurde bisher 3-mal zitiert (Crossref) und nennt 18 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: United States of America, Department of Energy-National Nuclear Security Administration), Stewardship Science Academic Program, Department of Energy-National Nuclear Security Administration (DOE-NNSA), Stewardship Science Academic Program.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

A thorough procedure was developed to efficiently manufacture dogbone samples using focused ion beam (FIB) milling for micro-tensile testing. A Bruker PI 89 PicoIndenter, Billerica, MA, USA, was used as a case study, although the analysis and results are applicable to other micro-mechanical testing systems capable of mounting a standard, Ø12.7 mm × Ø3.2 mm pin, scanning electron microscopy (SEM) pin stub (Ted Pella, Redding, CA, USA). Nine dogbones were made from an Fe-45Cu alloy additively manufactured using powder-fed laser-directed energy deposition (DED-LB). Testing showed that fracture was confined to the gauge section for all dogbones and that the fracture mode, ductile vs. brittle, was entirely dependent on the grain orientation relative to the loading direction. The analysis showed that the measured plastic strain to failure can vary from >11% (optimal geometry) to 1 GPa) metallic materials. Subsequently, a finite element analysis (FEA) was conducted to identify the improved dogbone geometries. A total of ten thousand dogbone geometries were tested, and their dimensions were defined by a set of four adjustable parameters (corner radius, load surface angle, load surface length, and dogbone head length). The gauge width and gauge length were fixed to 4 µm and 10 µm, respectively. Three-dimensional surface plots of the stress concentration as a function of two parameters were used to identify the optimal ranges of parameter values. The addition of maximum width and length constraints, measuring 25 µm and 30 µm, respectively, allowed us to identify an optimal geometry at load surface angles of 30° and 45°. Their respective dimensions (corner radius, load surface length, and dogbone head length) are, in µm, 12, 6, and 7 and 10, 7, and 7. Testing these two optimal geometries with a range of gauge lengths from 4 to 20 µm showed that smaller gauge lengths only slightly reduced the detrimental stress concentration outside the gauge section. However, smaller gauge lengths will notably improve the FIB surface polishing step as tapering is reduced with smaller dogbone lengths.

Schlagwörter

Stichwörter der Autor:innen

FEAFIBPI 89 PicoIndenteradditive manufacturingcopper–iron alloysdogbone geometryfinite element analysisfocused ion beam millingmicro-tensile testing

Autor:innen und Institutionen

  • Department of Materials Science and Engineering, University of Michigan, Ann Arbor, MI 48109, USA.
  • Sigma Division, Los Alamos National Laboratory, Los Alamos, NM 87545, USA.
  • Michigan Center for Materials Characterization, University of Michigan, Ann Arbor, MI 48109, USA.
  • Department of Mechanical Engineering, University of Michigan, Ann Arbor, MI 48109, USA.

ORCID-Profile: Daniel B Yin, Haiping Sun, Amit Misra

Förderung

  • United States of America, Department of Energy-National Nuclear Security Administration), Stewardship Science Academic Program
  • Department of Energy-National Nuclear Security Administration (DOE-NNSA), Stewardship Science Academic Program

Zitieren

APA

Yin, D. B., Sun, H., & Misra, A. (2024). Optimal Geometry for Focused Ion Beam-Milled Samples for Direct-Pull Micro-Tensile Testing Performed In Situ in a Scanning Electron Microscope. Materials, 17(21), 5144. https://doi.org/10.3390/ma17215144

Vancouver

Yin DB, Sun H, Misra A. Optimal Geometry for Focused Ion Beam-Milled Samples for Direct-Pull Micro-Tensile Testing Performed In Situ in a Scanning Electron Microscope. Materials. 2024;17(21):5144. doi:10.3390/ma17215144

BibTeX
@article{Yin2024,
  author = {Yin, Daniel B and Sun, Haiping and Misra, Amit},
  title = {Optimal Geometry for Focused Ion Beam-Milled Samples for Direct-Pull Micro-Tensile Testing Performed In Situ in a Scanning Electron Microscope},
  journal = {Materials},
  year = {2024},
  volume = {17},
  number = {21},
  pages = {5144},
  doi = {10.3390/ma17215144}
}
Kostenlos starten →