Investigation of High-Temperature Oxidation Behavior of Additive Manufactured CoCrMo Alloy for Mandrel Manufacturing
Materials · 24.07.2024 · 17 (15) · 3660
DOI: 10.3390/ma17153660 ↗Kurz gefasst
Fachartikel in der Zeitschrift Materials, online erschienen am 24.07.2024. Verfasst von Adina Cristina Toma und 5 weiteren Autor:innen. Beteiligte Einrichtung: Romanian Research and Development Institute for Gas Turbines COMOTI, 220D Iuliu Maniu Av., 061126 Bucharest, Romania. Die Arbeit wurde bisher 7-mal zitiert (Crossref) und nennt 35 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Romanian Ministry of Research, Innovation and Digitization.
Abstract (Originalsprache)
The cyclic oxidation behavior of an additive manufactured CoCrMo alloy with 0.14 wt.% C was investigated at 914 °C for 32 cycles, each lasting 10 h, resulting in a total exposure time of 320 h. The oxidation rate was assessed for mass gain after finishing each 40 h oxidation cycle. It was experimentally determined that the oxidative process at 914 °C of this CoCrMo alloy follows a parabolic law, with the process being fast at the beginning and slowing down after the first 40 h. The microstructural analysis revealed that in the as-printed state, the phases developed were primarily the γ matrix and minor traces of ε phase. The oxidative process ensured an increase in the ε phase and precipitation of carbides which produced a 12% increase in the material’s hardness after the first 40 h of exposure at 914 °C. The oxidation process led to the development of an oxide scale comprising a dense Cr2O3 layer and a porous layer of CoCr2O4 spinel, the latter spalling after the 240 h of exposure. Despite this spallation, the oxide scale continued to develop in the presence of O, Cr, and Co. The experimental analysis provided valuable insights regarding the material’s behavior under prolonged exposure at high temperature in air, demonstrating its suitability as a candidate for additive manufactured mandrels used for bending metallic pipe fitting elbows.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Romanian Research and Development Institute for Gas Turbines COMOTI, 220D Iuliu Maniu Av., 061126 Bucharest, Romania.
- National Institute for Research and Development in Electrical Engineering, ICPE-CA, 313 Splaiul Unirii, 030138 Bucharest, Romania.
- National Institute of Research and Development in Mechatronics and Measurement Technique-INCDMTM, Pantelimon Str. No. 6-8, 022401 Bucharest, Romania.
- Doctoral School of Materials Science and Engineering, National University of Science and Technology Politehnica Bucharest, 313 Splaiul Independenței, 060042 Bucharest, Romania.
ORCID-Profile: Mihaela Raluca Condruz, Alexandru Paraschiv, Teodor Adrian Badea, Delia Pătroi, Nicoleta Mirela Popa
Förderung
- Romanian Ministry of Research, Innovation and Digitization
Zitieren
APA
Toma, A. C., Condruz, M. R., Paraschiv, A., Badea, T. A., Pătroi, D., & Popa, N. M. (2024). Investigation of High-Temperature Oxidation Behavior of Additive Manufactured CoCrMo Alloy for Mandrel Manufacturing. Materials, 17(15), 3660. https://doi.org/10.3390/ma17153660
Vancouver
Toma AC, Condruz MR, Paraschiv A, Badea TA, Pătroi D, Popa NM. Investigation of High-Temperature Oxidation Behavior of Additive Manufactured CoCrMo Alloy for Mandrel Manufacturing. Materials. 2024;17(15):3660. doi:10.3390/ma17153660
BibTeX
@article{Toma2024,
author = {Toma, Adina Cristina and Condruz, Mihaela Raluca and Paraschiv, Alexandru and Badea, Teodor Adrian and Pătroi, Delia and Popa, Nicoleta Mirela},
title = {Investigation of High-Temperature Oxidation Behavior of Additive Manufactured CoCrMo Alloy for Mandrel Manufacturing},
journal = {Materials},
year = {2024},
volume = {17},
number = {15},
pages = {3660},
doi = {10.3390/ma17153660}
}
EUVIMED