EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

High Temperature Oxidation Behavior of Additive Manufactured Ti6Al4V Alloy with the Addition of Yttrium Oxide Nanoparticles

Qiang Wang, Pu Song, Wenjuan Niu, Nan Li, Ning Hu

Materials · 24.05.2024 · 17 (11) · 2544

DOI: 10.3390/ma17112544 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 24.05.2024. Verfasst von Qiang Wang und 4 weiteren Autor:innen. Beteiligte Einrichtung: School of Metallurgical Engineering, Xi'an University of Architecture and Technology, Xi'an 710055, China. Die Arbeit wurde bisher 13-mal zitiert (Crossref) und nennt 32 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Education Department of Shaanxi Province, Key Science and Technology program of Shaanxi Province.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Titanium alloys face challenges of high temperature oxidation during the service period when used as aircraft engine components. In this paper, the effect of Y2O3 addition on the oxidation behavior and the microstructural change of the Ti6Al4V alloy fabricated by selective laser melting (SLM) was comprehensively studied. The results show that the surface of the Ti6Al4V alloy is a dense oxide layer composed of TiO2 and Al2O3 compounds. The thickness of the oxide layer of the Ti6Al4V increased from 59.55 μm to 139.15 μm. In contrast, with the addition of Y2O3, the thickness of the oxide layer increased from 35.73 μm to 80.34 μm. This indicates that the thickness of the oxide layer formation was a diffusion-controlled process and, therefore, the thickness of the oxide layer increased with an increase in temperature. The Ti6Al4V-1.0 wt.% Y2O3 alloy exhibits excellent oxidation resistance, and the thickness is significantly lower than that of the Ti6Al4V alloy. The oxidation kinetics of the Ti6Al4V and Ti6Al4V-1.0 wt.% Y2O3 alloys at 600 °C and 800 °C follows a parabolic rule, whereas the oxidation of the Ti6Al4V and Ti6Al4V-1.0 wt.% Y2O3 alloys at 1000 °C follows the linear law. The average microhardness values of Ti6Al4V samples after oxidation increased to 818.9 ± 20 HV0.5 with increasing temperature, and the average microhardness values of the Ti6Al4V-1.0 wt.% Y2O3 alloy increases until 800 °C and then decreases at 1000 °C. The addition of Y2O3 shows a significant improvement in the microhardness during the different temperatures after oxidation.

Schlagwörter

Stichwörter der Autor:innen

Ti6Al4Vadditive manufacturingmicrohardnessoxidation behaviorsurface

Autor:innen und Institutionen

  • School of Metallurgical Engineering, Xi'an University of Architecture and Technology, Xi'an 710055, China.
  • Shaanxi Province Metallurgical Engineering Technology Research Center, Xi'an 710055, China.

Förderung

  • Education Department of Shaanxi Province
  • Key Science and Technology program of Shaanxi Province

Zitieren

APA

Wang, Q., Song, P., Niu, W., Li, N., & Hu, N. (2024). High Temperature Oxidation Behavior of Additive Manufactured Ti6Al4V Alloy with the Addition of Yttrium Oxide Nanoparticles. Materials, 17(11), 2544. https://doi.org/10.3390/ma17112544

Vancouver

Wang Q, Song P, Niu W, Li N, Hu N. High Temperature Oxidation Behavior of Additive Manufactured Ti6Al4V Alloy with the Addition of Yttrium Oxide Nanoparticles. Materials. 2024;17(11):2544. doi:10.3390/ma17112544

BibTeX
@article{Wang2024,
  author = {Wang, Qiang and Song, Pu and Niu, Wenjuan and Li, Nan and Hu, Ning},
  title = {High Temperature Oxidation Behavior of Additive Manufactured Ti6Al4V Alloy with the Addition of Yttrium Oxide Nanoparticles},
  journal = {Materials},
  year = {2024},
  volume = {17},
  number = {11},
  pages = {2544},
  doi = {10.3390/ma17112544}
}
Kostenlos starten →