EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Bending Strength of Continuous Fiber-Reinforced (CFR) Polyamide-Based Composite Additively Manufactured through Material Extrusion

Maciej Łakomy, Janusz Kluczyński iD, Bartłomiej Sarzyński iD, Katarzyna Jasik iD, Ireneusz Szachogłuchowicz iD, Jakub Łuszczek iD

Materials · 15.06.2024 · 17 (12) · 2937

DOI: 10.3390/ma17122937 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 15.06.2024. Verfasst von Maciej Łakomy und 5 weiteren Autor:innen. Beteiligte Einrichtung: Institute of Robots & Machine Design, Faculty of Mechanical Engineering, Military University of Technology, Gen. S. Kaliskiego St., 00-908 Warsaw, Po…. Die Arbeit wurde bisher 11-mal zitiert (Crossref) und nennt 49 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Military University of Technology in Warsaw, Military University of Technology.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This paper shows the three-point bending strength analysis of a composite material consisting of polyamide doped with chopped carbon fiber and reinforced with continuous carbon fiber produced by means of the material extrusion (MEX) additive manufacturing technique. For a comparison, two types of specimens were produced: unreinforced and continuous fiber-reinforced (CFR) with the use of carbon fiber. The specimens were fabricated in two orientations that assure the highest strength properties. Strength analysis was supplemented by additional digital image correlation (DIC) analysis that allowed for the identification of regions with maximum strain within the specimens. The utilization of an optical microscope enabled a fractographic examination of the fracture surfaces of the specimens. The results of this study demonstrated a beneficial effect of continuous carbon fiber reinforcement on both the stiffness and strength of the material, with an increase in flexural strength from 77.34 MPa for the unreinforced composite to 147.03 MPa for the composite reinforced with continuous carbon fiber.

Schlagwörter

Stichwörter der Autor:innen

DICFDMFFFMEXOnyxcarbonflexural strengthfracture analysisthree-point tests

Autor:innen und Institutionen

  • Institute of Robots & Machine Design, Faculty of Mechanical Engineering, Military University of Technology, Gen. S. Kaliskiego St., 00-908 Warsaw, Poland.

ORCID-Profile: Janusz Kluczyński, Bartłomiej Sarzyński, Katarzyna Jasik, Ireneusz Szachogłuchowicz, Jakub Łuszczek

Förderung

  • Military University of Technology in Warsaw
  • Military University of Technology

Zitieren

APA

Łakomy, M., Kluczyński, J., Sarzyński, B., Jasik, K., Szachogłuchowicz, I., & Łuszczek, J. (2024). Bending Strength of Continuous Fiber-Reinforced (CFR) Polyamide-Based Composite Additively Manufactured through Material Extrusion. Materials, 17(12), 2937. https://doi.org/10.3390/ma17122937

Vancouver

Łakomy M, Kluczyński J, Sarzyński B, Jasik K, Szachogłuchowicz I, Łuszczek J. Bending Strength of Continuous Fiber-Reinforced (CFR) Polyamide-Based Composite Additively Manufactured through Material Extrusion. Materials. 2024;17(12):2937. doi:10.3390/ma17122937

BibTeX
@article{akomy2024,
  author = {Łakomy, Maciej and Kluczyński, Janusz and Sarzyński, Bartłomiej and Jasik, Katarzyna and Szachogłuchowicz, Ireneusz and Łuszczek, Jakub},
  title = {Bending Strength of Continuous Fiber-Reinforced (CFR) Polyamide-Based Composite Additively Manufactured through Material Extrusion},
  journal = {Materials},
  year = {2024},
  volume = {17},
  number = {12},
  pages = {2937},
  doi = {10.3390/ma17122937}
}
Kostenlos starten →