Post-Processing Effect on the Corrosion Resistance of Super Duplex Stainless Steel Produced by Laser Powder Bed Fusion
Materials · 08.06.2024 · 17 (12) · 2807
DOI: 10.3390/ma17122807 ↗Kurz gefasst
Fachartikel in der Zeitschrift Materials, online erschienen am 08.06.2024. Verfasst von Zbigniew Brytan und 4 weiteren Autor:innen. Beteiligte Einrichtung: Department of Engineering Materials and Biomaterials, Faculty of Mechanical Engineering, Silesian University of Technology, 44-100 Gliwice, Poland. Die Arbeit wurde bisher 12-mal zitiert (Crossref) und nennt 39 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: International Visegrad Fund, MSCA, International Visegrad Fund Fellowship.
Abstract (Originalsprache)
This study examines the microstructural characteristics and corrosion resistance of super duplex stainless steel (SDSS) produced through laser powder bed fusion (LPBF). The analysis shows that the as-printed samples mainly exhibit a ferritic microstructure, which is due to the fast-cooling rates of the LPBF technique. X-ray and microstructure analyses reveal the presence of minor austenite phases in the ferritic matrix. The process of solution annealing led to a more balanced microstructure. Analyses of corrosion resistance, such as potentiodynamic polarization tests and EIS, indicate that heat treatment has a significant impact on the corrosion behavior of SDSS. Solution annealing and stress relieving at 400 °C for 1 h can improve corrosion resistance by increasing polarization resistance and favorable EIS parameters. However, stress relieving at 550 °C for 5 h may reduce the material’s corrosion resistance due to the formation of chromium nitride. Therefore, stress relieving at 400 °C for 1 h is a practical method to significantly enhance the corrosion resistance of LPBF-printed SDSS. This method offers a balance between microstructural integrity and material performance.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Department of Engineering Materials and Biomaterials, Faculty of Mechanical Engineering, Silesian University of Technology, 44-100 Gliwice, Poland.
- Department of Plastic Deformation and Simulation Processes, Institute of Materials and Quality Engineering, Faculty of Materials Metallurgy and Recycling, Technical University of Kosice, Park Komenského 11, 04001 Kosice…
- Bodva Industry and Innovation Cluster, Budulov 174, 04501 Moldava nad Bodvou, Slovakia.
- Advanced Research and Innovation Hub, Budulov 174, 04501 Moldava and Bodvou, Slovakia.
- Centre of Advanced Manufacturing and Material Processing (AMMP Centre), Universiti Malaya, Kuala Lumpur 50603, Malaysia.
ORCID-Profile: Zbigniew Brytan, Mengistu Dagnaw, Jana Bidulská, Róbert Bidulský, Mohd Ridha Muhamad
Förderung
- International Visegrad Fund
- MSCA
- International Visegrad Fund Fellowship
- European Union’s Horizon programme under the Marie Skłodowska-Curie Actions MSCA Staff Exchanges
- Minister of Science and Higher Education’s
Zitieren
APA
Brytan, Z., Dagnaw, M., Bidulská, J., Bidulský, R., & Muhamad, M. R. (2024). Post-Processing Effect on the Corrosion Resistance of Super Duplex Stainless Steel Produced by Laser Powder Bed Fusion. Materials, 17(12), 2807. https://doi.org/10.3390/ma17122807
Vancouver
Brytan Z, Dagnaw M, Bidulská J, Bidulský R, Muhamad MR. Post-Processing Effect on the Corrosion Resistance of Super Duplex Stainless Steel Produced by Laser Powder Bed Fusion. Materials. 2024;17(12):2807. doi:10.3390/ma17122807
BibTeX
@article{Brytan2024,
author = {Brytan, Zbigniew and Dagnaw, Mengistu and Bidulská, Jana and Bidulský, Róbert and Muhamad, Mohd Ridha},
title = {Post-Processing Effect on the Corrosion Resistance of Super Duplex Stainless Steel Produced by Laser Powder Bed Fusion},
journal = {Materials},
year = {2024},
volume = {17},
number = {12},
pages = {2807},
doi = {10.3390/ma17122807}
}
EUVIMED