EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Experimental Investigation of Water Jet-Guided Laser Micro-Hole Drilling of Cf/SiC Composites

Binying Bao iD, Guangyi Zhang, Zhongan Chen, Yang Chao, Chunhai Guo, Wenwu Zhang

Materials · 24.04.2024 · 17 (9) · 1975

DOI: 10.3390/ma17091975 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 24.04.2024. Verfasst von Binying Bao und 5 weiteren Autor:innen. Beteiligte Einrichtung: College of Mechanical Engineering, Zhejiang University of Technology, Hangzhou 310023, China. Die Arbeit wurde bisher 26-mal zitiert (Crossref) und nennt 50 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: National Natural Science Foundation of China, Natural Science Foundation of Zhejiang Province, Innovation Guidance Foundation of Innovation Academy for Light-duty Gas Turbine of Chinese Academy of Sciences.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

In this paper, water jet-guided laser (WJGL) drilling of Cf/SiC composites was employed and the effects of the processing parameters on the depth and quality of the micro-holes were systematically investigated. Firstly, the depth measurement showed that the increase in processing time and power density led to a significant improvement in micro-hole drilling depth. However, the enhancement of the water jet speed resulted in a pronounced decrease in the depth due to the phenomenon of water splashing. In contrast, the scanning speed, path overlap ratio, pulse frequency, and helium pressure exhibited less effect on the micro-hole depth. Secondly, the microstructural analysis revealed that the increase in power density resulted in the deformation and fracture of the carbon fibers, while the augmentation in water jet speed reduced the thermal defects. Finally, based on the optimization of the processing parameters, a micro-hole of exceptional quality was achieved, with a depth-to-diameter ratio of 8.03 and a sidewall taper of 0.72°. This study can provide valuable guidance for WJGL micro-hole drilling of Cf/SiC composites.

Schlagwörter

Stichwörter der Autor:innen

Cf/SiC compositesinfluencing factormicro-hole drillingmicrostructure analysiswater jet-guided laser

Autor:innen und Institutionen

  • College of Mechanical Engineering, Zhejiang University of Technology, Hangzhou 310023, China.
  • Ningbo Institute of Materials Technology and Engineering, Chinese Academy of Sciences, Ningbo 315201, China.

ORCID-Profile: Binying Bao

Förderung

  • National Natural Science Foundation of China
  • Natural Science Foundation of Zhejiang Province
  • Innovation Guidance Foundation of Innovation Academy for Light-duty Gas Turbine of Chinese Academy of Sciences
  • Natural Science Foundation of Ningbo
  • Open Subject of State Key Laboratory of Intelligent Manufacturing Equipment and Technology
  • Ningbo Yongjiang Talent Introduction Programme
  • Innovation Academy for Light-duty Gas Turbine of the Chinese Academy of Sciences

Zitieren

APA

Bao, B., Zhang, G., Chen, Z., Chao, Y., Guo, C., & Zhang, W. (2024). Experimental Investigation of Water Jet-Guided Laser Micro-Hole Drilling of Cf/SiC Composites. Materials, 17(9), 1975. https://doi.org/10.3390/ma17091975

Vancouver

Bao B, Zhang G, Chen Z, Chao Y, Guo C, Zhang W. Experimental Investigation of Water Jet-Guided Laser Micro-Hole Drilling of Cf/SiC Composites. Materials. 2024;17(9):1975. doi:10.3390/ma17091975

BibTeX
@article{Bao2024,
  author = {Bao, Binying and Zhang, Guangyi and Chen, Zhongan and Chao, Yang and Guo, Chunhai and Zhang, Wenwu},
  title = {Experimental Investigation of Water Jet-Guided Laser Micro-Hole Drilling of Cf/SiC Composites},
  journal = {Materials},
  year = {2024},
  volume = {17},
  number = {9},
  pages = {1975},
  doi = {10.3390/ma17091975}
}
Kostenlos starten →