EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Dislocation Hardening in a New Manufacturing Route of Ferritic Oxide Dispersion-Strengthened Fe-14Cr Cladding Tube

Freddy Salliot, András Borbély, Denis Sornin iD, Roland Logé iD, Gabriel Spartacus, Hadrien Leguy, Thierry Baudin iD, Yann de Carlan

Materials · 01.03.2024 · 17 (5) · 1146

DOI: 10.3390/ma17051146 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 01.03.2024. Verfasst von Freddy Salliot und 7 weiteren Autor:innen. Beteiligte Einrichtung: Université Paris-Saclay, CEA, Service de Recherche en Matériaux et Procédés Avancés, 91191 Gif-sur-Yvette, France. Die Arbeit wurde bisher 5-mal zitiert (Crossref) und nennt 57 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The microstructure evolution associated with the cold forming sequence of an Fe-14Cr-1W-0.3Ti-0.3Y2O3 grade ferritic stainless steel strengthened by dispersion of nano oxides (ODS) was investigated. The material, initially hot extruded at 1100 °C and then shaped into cladding tube geometry via HPTR cold pilgering, shows a high microstructure stability that affects stress release heat treatment efficiency. Each step of the process was analyzed to better understand the microstructure stability of the material. Despite high levels of stored energy, heat treatments, up to 1350 °C, do not allow for recrystallization of the material. The Vickers hardness shows significant variations along the manufacturing steps. Thanks to a combination of EBSD and X-ray diffraction measurements, this study gives a new insight into the contribution of statistically stored dislocation (SSD) recovery on the hardness evolution during an ODS steel cold forming sequence. SSD density, close to 4.1015 m−2 after cold rolling, drops by only an order of magnitude during heat treatment, while geometrically necessary dislocation (GND) density, close to 1.1015 m−2, remains stable. Hardness decrease during heat treatments appears to be controlled only by the evolution of SSD.

Schlagwörter

Stichwörter der Autor:innen

EBSDODS steelX-ray diffractioncold rollingdislocation densitymicrostructure

Autor:innen und Institutionen

  • Université Paris-Saclay, CEA, Service de Recherche en Matériaux et Procédés Avancés, 91191 Gif-sur-Yvette, France.
  • Mines Saint-Etienne, Univ. Lyon, CNRS, UMR 5307 LGF, Centre SMS, F-42023 Saint-Etienne, France.
  • Thermomechanical Metallurgy Laboratory (LMTM)-PX Group Chair, École Polytechnique Fédérale de Lausanne (EPFL), CH-2002 Neuchâtel, Switzerland.
  • Department of Materials Science and Engineering, KTH Royal Institute of Technology, SE-100 44 Stockholm, Sweden.
  • Université Paris-Saclay, CNRS, Institut de Chimie Moléculaire et des Matériaux d'Orsay, 91405 Orsay, France.

ORCID-Profile: Denis Sornin, Roland Logé, Thierry Baudin

Zitieren

APA

Salliot, F., Borbély, A., Sornin, D., Logé, R., Spartacus, G., Leguy, H., Baudin, T., & de Carlan, Y. (2024). Dislocation Hardening in a New Manufacturing Route of Ferritic Oxide Dispersion-Strengthened Fe-14Cr Cladding Tube. Materials, 17(5), 1146. https://doi.org/10.3390/ma17051146

Vancouver

Salliot F, Borbély A, Sornin D, Logé R, Spartacus G, Leguy H, et al. Dislocation Hardening in a New Manufacturing Route of Ferritic Oxide Dispersion-Strengthened Fe-14Cr Cladding Tube. Materials. 2024;17(5):1146. doi:10.3390/ma17051146

BibTeX
@article{Salliot2024,
  author = {Salliot, Freddy and Borbély, András and Sornin, Denis and Logé, Roland and Spartacus, Gabriel and Leguy, Hadrien and Baudin, Thierry and de Carlan, Yann},
  title = {Dislocation Hardening in a New Manufacturing Route of Ferritic Oxide Dispersion-Strengthened Fe-14Cr Cladding Tube},
  journal = {Materials},
  year = {2024},
  volume = {17},
  number = {5},
  pages = {1146},
  doi = {10.3390/ma17051146}
}
Kostenlos starten →