EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Tribological Properties of a Sliding Joint with an a-C:H:W Coating under Lubrication Conditions with PAO8 Oil and the Addition of 2% MoS2 Nanoparticles

Krystian Hadło, Janusz Lubas iD, Wojciech Szczypinski-Sala, Agnieszka Tomala iD, Dariusz Konieczny

Materials · 13.02.2024 · 17 (4) · 870

DOI: 10.3390/ma17040870 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 13.02.2024. Verfasst von Krystian Hadło und 4 weiteren Autor:innen. Beteiligte Einrichtung: Faculty of Mechanical Engineering and Aeronautics, Rzeszow University of Technology, Powstańców Warszawy 8 Av., 35-959 Rzeszow, Poland. Die Arbeit wurde bisher 3-mal zitiert (Crossref) und nennt 54 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

One of the promising methods for improving the durability and reliability of friction joints in combustion engines is the use of thin and hard coatings, including coatings based on amorphous DLC. The a-C:H:W coating was produced using the commercial PVD method. The tested tribological joints were made of AISI 4337 steel and SAE-48 bearing alloy (conformal contact) and AISI 4337 steel and valve shims (non-conformal contact). The contact area was lubricated with SAE 5W40 engine oil and PAO8 oil + 2 wt.% MoS2 nanoparticles. The objective of this work is to explore the influence of PAO8 + MoS2 on the tribological properties of a sliding joint with an a-C:H:W coating and the change in the properties of the oils. In the conformal contact, the lubrication of the a-C:H:W coating with PAO8 + MoS2 caused a significant increase in the friction resistance (than in) as compared to the joints with a quenching and tempering surface layer and lubricated SAE 5W40, while in the non-conformal contact, the lubrication of the a-C:H:W coating with PAO8 + MoS2 caused a decrease in the friction resistance and temperature of the contact area. The joints with the a-C:H:W coating were characterized by higher wear of the SAE-48 bearing alloy, as compared to the joints with the surface layer without coating (lubricated with SAE 5W40 oil—11-fold increase, PAO8 + MoS2—46-fold increase). The wear of valve shims with the a-C:H:W coating was significantly lower as compared to the wear of the commercial version of the valve shims (the difference between joints lubricated with SAE 5W40 oil and PAO8 + MoS2 was 12%, 36% and 29% for unit pressures of 10, 15 and 20 MPa). Lubrication of the a-C:H:W coating with PAO8 oil + MoS2 protected the sliding joints against seizing in non-conformal contact.

Schlagwörter

Stichwörter der Autor:innen

DLCMoS2coatingengine oilfrictionsurface layerwear

Autor:innen und Institutionen

  • Faculty of Mechanical Engineering and Aeronautics, Rzeszow University of Technology, Powstańców Warszawy 8 Av., 35-959 Rzeszow, Poland.
  • Faculty of Mechanical Engineering, Cracow University of Technology, 37 Jana Pawła II Av., 31-864 Krakow, Poland.
  • Faculty of Materials Engineering and Physics, Cracow University of Technology, 37 Jana Pawła II Av., 31-864 Krakow, Poland.

ORCID-Profile: Janusz Lubas, Agnieszka Tomala

Zitieren

APA

Hadło, K., Lubas, J., Szczypinski-Sala, W., Tomala, A., & Konieczny, D. (2024). Tribological Properties of a Sliding Joint with an a-C:H:W Coating under Lubrication Conditions with PAO8 Oil and the Addition of 2% MoS2 Nanoparticles. Materials, 17(4), 870. https://doi.org/10.3390/ma17040870

Vancouver

Hadło K, Lubas J, Szczypinski-Sala W, Tomala A, Konieczny D. Tribological Properties of a Sliding Joint with an a-C:H:W Coating under Lubrication Conditions with PAO8 Oil and the Addition of 2% MoS2 Nanoparticles. Materials. 2024;17(4):870. doi:10.3390/ma17040870

BibTeX
@article{Hado2024,
  author = {Hadło, Krystian and Lubas, Janusz and Szczypinski-Sala, Wojciech and Tomala, Agnieszka and Konieczny, Dariusz},
  title = {Tribological Properties of a Sliding Joint with an a-C:H:W Coating under Lubrication Conditions with PAO8 Oil and the Addition of 2% MoS2 Nanoparticles},
  journal = {Materials},
  year = {2024},
  volume = {17},
  number = {4},
  pages = {870},
  doi = {10.3390/ma17040870}
}
Kostenlos starten →