Microstructure and Mechanical Properties of Al–Li Alloys with Different Li Contents Prepared by Selective Laser Melting
Materials · 29.01.2024 · 17 (3) · 657
DOI: 10.3390/ma17030657 ↗Kurz gefasst
Fachartikel in der Zeitschrift Materials, online erschienen am 29.01.2024. Verfasst von Shuobing Shao und 4 weiteren Autor:innen. Beteiligte Einrichtung: National Engineering & Technology Research Center for Non-Ferrous Metals Composites, GRINM Group Corporation Limited, Beijing 101407, China. Die Arbeit wurde bisher 17-mal zitiert (Crossref) und nennt 64 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: GRINM Metal Composites Technology Co., Ltd., National Engineering & Technology Research Center for Non-ferrous Metal Matrix Composites, GRINM Group Co., Ltd., National Engineering & Technology Research Center for Non-ferrous Metal Matrix Composites, GRINM Group Co., Ltd..
Abstract (Originalsprache)
Research on the development of new lightweight Al–Li alloys using a selective laser melting process has great potential for industrial applications. This paper reports on the development of novel aluminum–lithium alloys using selective laser melting technology. Al–Cu–Li–Mg–Ag–Sc–Zr pre-alloyed powders with lithium contents of 1 wt.%, 2 wt.% and 3 wt.%, respectively, were prepared by inert gas atomization. After SLM process optimization, the microstructure and mechanical properties of the as-printed specimens were investigated. The densifications of the three newly developed alloys were 99.51%, 98.96% and 92.01%, respectively. They all had good formability, with the lithium loss rate at about 15%. The as-printed alloy with 1% Li content presented good comprehensive properties, with a yield strength of 413 ± 16 MPa, an ultimate tensile strength of 461 ± 12 MPa, and an elongation of 14 ± 1%. The three alloys exhibited a layered molten pool stacking morphology and had a typical heterostructure. The columnar crystals and equiaxed fine grains were alternately arranged, and most of the precipitated phases were enriched at the grain boundaries. The change in Li content mainly affected the precipitation of the Cu-containing phase. When the Li content was 1 wt.%, the following occured: θ phase, T1 phase and TB phase. When Li increased to 2 wt.%, T1 and T2 phases precipitated together. When Li reaches 3 wt.%, δ’ phase precipitated with T2 phase. This study provides useful guidance for the future SLM forming of new crack-free and high-strength Al–Li alloys.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- National Engineering & Technology Research Center for Non-Ferrous Metals Composites, GRINM Group Corporation Limited, Beijing 101407, China.
- GRINM Metal Composites Technology Co., Ltd., Beijing 101407, China.
- General Research Institute for Nonferrous Metals, Beijing 100088, China.
ORCID-Profile: Shuobing Shao, Zhuoheng Liang, Peng Yin
Förderung
- GRINM Metal Composites Technology Co., Ltd.
- National Engineering & Technology Research Center for Non-ferrous Metal Matrix Composites, GRINM Group Co., Ltd.
- National Engineering & Technology Research Center for Non-ferrous Metal Matrix Composites, GRINM Group Co., Ltd.
Zitieren
APA
Shao, S., Liang, Z., Yin, P., Li, X., & Zhang, Y. (2024). Microstructure and Mechanical Properties of Al–Li Alloys with Different Li Contents Prepared by Selective Laser Melting. Materials, 17(3), 657. https://doi.org/10.3390/ma17030657
Vancouver
Shao S, Liang Z, Yin P, Li X, Zhang Y. Microstructure and Mechanical Properties of Al–Li Alloys with Different Li Contents Prepared by Selective Laser Melting. Materials. 2024;17(3):657. doi:10.3390/ma17030657
BibTeX
@article{Shao2024,
author = {Shao, Shuobing and Liang, Zhuoheng and Yin, Peng and Li, Xinyuan and Zhang, Yongzhong},
title = {Microstructure and Mechanical Properties of Al–Li Alloys with Different Li Contents Prepared by Selective Laser Melting},
journal = {Materials},
year = {2024},
volume = {17},
number = {3},
pages = {657},
doi = {10.3390/ma17030657}
}
EUVIMED