EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Microstructure and Wear Resistance of Ti6Al4V Titanium Alloy Laser-Clad Ni60/WC Composite Coating

Mingjia Feng, Yunhai Ma, Yitong Tian, Hongtu Cao

Materials · 04.01.2024 · 17 (1) · 264

DOI: 10.3390/ma17010264 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 04.01.2024. Verfasst von Mingjia Feng und 3 weiteren Autor:innen. Beteiligte Einrichtung: The College of Biological and Agricultural Engineering, Jilin University, 5988 Renmin Street, Changchun 130025, China. Die Arbeit wurde bisher 21-mal zitiert (Crossref) und nennt 48 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: National Natural Science Foundation of China, Jilin Province Science and Technology Development Plan Item, Scientific Research Project of Jilin Provincial Education Department.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

In this paper, Ni60/WC wear-resistant coatings have been created on the Ti6Al4V substrate surface using a pre-layered powder laser cladding method by deploying various scanning speeds of 8, 10, 12, and 14 mm/s. The coatings are characterized through X-ray diffraction (XRD), scanning electron microscopy (SEM), and a high-speed reciprocating fatigue wear tester. It is found that the phase composition of the coating comprises the synthesized, hard phase TiC and TiB2, the silicides WSi2 and W5Si3, and NiTi and γ-Ni solid solutions. At different scanning speeds, there is a metallurgical fusion line in the bonding area of the fused cladding layer, indicating a good metallurgical bonding between the substrate and the powder. At a low scanning speed, the coating develops into coarse dendrites, which shows significant improvement with scanning speed. The microhardness first increases and then decreases with the scanning speed, and the coating’s average microhardness was 2.75–3.13 times higher than that of the substrate. The amount of mass wear has been reduced by 60.1–79.7% compared to the substrate. The wear behavior of the coatings was studied through detailed analysis of wear surfaces’ microstructures and the amount of wear to identify the optimum scanning speed.

Schlagwörter

Stichwörter der Autor:innen

Ni60/WClaser claddingscanning speedtitanium alloyswear behavior

Autor:innen und Institutionen

  • The College of Biological and Agricultural Engineering, Jilin University, 5988 Renmin Street, Changchun 130025, China.
  • School of Mechanical and Civil Engineering, Jilin Agricultural Science and Technology University, Jilin 132101, China.
  • Key Laboratory of Bionic Engineering, Ministry of Education, Jilin University, 5988 Renmin Street, Changchun 130025, China.

Förderung

  • National Natural Science Foundation of China
  • Jilin Province Science and Technology Development Plan Item
  • Scientific Research Project of Jilin Provincial Education Department
  • Foundation for Development of Science and Technology of Jilin Province

Zitieren

APA

Feng, M., Ma, Y., Tian, Y., & Cao, H. (2024). Microstructure and Wear Resistance of Ti6Al4V Titanium Alloy Laser-Clad Ni60/WC Composite Coating. Materials, 17(1), 264. https://doi.org/10.3390/ma17010264

Vancouver

Feng M, Ma Y, Tian Y, Cao H. Microstructure and Wear Resistance of Ti6Al4V Titanium Alloy Laser-Clad Ni60/WC Composite Coating. Materials. 2024;17(1):264. doi:10.3390/ma17010264

BibTeX
@article{Feng2024,
  author = {Feng, Mingjia and Ma, Yunhai and Tian, Yitong and Cao, Hongtu},
  title = {Microstructure and Wear Resistance of Ti6Al4V Titanium Alloy Laser-Clad Ni60/WC Composite Coating},
  journal = {Materials},
  year = {2024},
  volume = {17},
  number = {1},
  pages = {264},
  doi = {10.3390/ma17010264}
}
Kostenlos starten →