EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Experimental and Numerical Investigation on the Aerosol Micro-Jet 3D Printing of Flexible Electronic Devices

Yuanming Zhang, Tao Zhu, Junke Jiao, Shiyu Song, Zhenqian Wang iD, Ziwen Wang

Materials · 09.11.2023 · 16 (22) · 7099

DOI: 10.3390/ma16227099 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 09.11.2023. Verfasst von Yuanming Zhang und 5 weiteren Autor:innen. Beteiligte Einrichtung: School of Mechanical and Vehicle Engineering, Linyi University, Linyi 276000, China. Die Arbeit wurde bisher 8-mal zitiert (Crossref) und nennt 28 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: the Natural Science Foundation of Shandong Province, Shandong Province Innovation Capacity Improvement Project Funding Project, Natural Science Foundation of Shandong Province.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

In this study, the optimal forming parameters for printing flexible circuits using aerosol jet printing technology are explored through numerical simulation and experiments. The printhead during the deposition process is numerically simulated. By employing the controlled variable method, the process parameters such as gas flow rate, working distance, nozzle diameter, and printing speed are selected to investigate their effects on the morphology of the printed lines. Accordingly, single-factor experiments are designed to validate the printing of flexible circuits on both planar and curved substrates. Laser micro-sintering is utilized to improve the conductivity of the printed lines and ultimately fabricate flexible strain sensors. Under the sheath gas flow rate of 400 sccm, carrier gas flow rate of 100 sccm, working distance of 3 mm, nozzle diameter of 500 μm, and printing speed of 10 mm/s, the optimal morphology of the printed lines is achieved with low linewidth characteristics. The variations in the focal ratio, working distance, nozzle diameter, and printing speed significantly affect the minimum feature line width and morphology of the printed lines.

Schlagwörter

Stichwörter der Autor:innen

additive manufacturingaerosol micro-jet printingexperimental verificationflexible electronicsprocess researchsimulation analysis

Autor:innen und Institutionen

  • School of Mechanical and Vehicle Engineering, Linyi University, Linyi 276000, China.
  • School of Automation and Electrical Engineering, Linyi University, Linyi, 276000, China.
  • School of Mechanical Engineering, Yangzhou University, Yangzhou 225009, China.

ORCID-Profile: Zhenqian Wang

Förderung

  • the Natural Science Foundation of Shandong Province
  • Shandong Province Innovation Capacity Improvement Project Funding Project
  • Natural Science Foundation of Shandong Province

Zitieren

APA

Zhang, Y., Zhu, T., Jiao, J., Song, S., Wang, Z., & Wang, Z. (2023). Experimental and Numerical Investigation on the Aerosol Micro-Jet 3D Printing of Flexible Electronic Devices. Materials, 16(22), 7099. https://doi.org/10.3390/ma16227099

Vancouver

Zhang Y, Zhu T, Jiao J, Song S, Wang Z, Wang Z. Experimental and Numerical Investigation on the Aerosol Micro-Jet 3D Printing of Flexible Electronic Devices. Materials. 2023;16(22):7099. doi:10.3390/ma16227099

BibTeX
@article{Zhang2023,
  author = {Zhang, Yuanming and Zhu, Tao and Jiao, Junke and Song, Shiyu and Wang, Zhenqian and Wang, Ziwen},
  title = {Experimental and Numerical Investigation on the Aerosol Micro-Jet 3D Printing of Flexible Electronic Devices},
  journal = {Materials},
  year = {2023},
  volume = {16},
  number = {22},
  pages = {7099},
  doi = {10.3390/ma16227099}
}
Kostenlos starten →