EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Modelling the Kerf Angle, Roughness and Waviness of the Surface of Inconel 718 in an Abrasive Water Jet Cutting Process

Marcin Płodzień iD, Łukasz Żyłka iD, Krzysztof Żak iD, Szymon Wojciechowski iD

Materials · 27.07.2023 · 16 (15) · 5288

DOI: 10.3390/ma16155288 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 27.07.2023. Verfasst von Marcin Płodzień und 3 weiteren Autor:innen. Beteiligte Einrichtung: Department of Manufacturing Techniques and Automation, The Faculty of Mechanical Engineering and Aeronautics, Rzeszow University of Technology, W. Po…. Die Arbeit wurde bisher 14-mal zitiert (Crossref) und nennt 26 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

An experimental study of the abrasive water jet cutting process of Inconel 718 alloy samples with varying values of cutting speed, abrasive flow rate and cutting material height was carried out. Surface roughness and waviness were measured at different cutting depths, and the variation of the kerf angle was studied. It was shown that the depth of cut has the greatest effect on roughness and waviness. The height of the sample has no impact on the roughness and waviness at a particular depth of cut. As the depth of cut increases, in most cases, roughness and waviness increase as well. It has been proven that the cutting speed has a negligible effect on surface roughness, but it has a significant effect on surface waviness. The waviness, on the other hand, depends only slightly on the abrasive flow. It has been proven that the kerf angle does not depend on the abrasive flow. The kerf angle depends mainly on the height of the sample. The models were developed for the parameters of roughness Ra and Rz, waviness Wa and Wz and kerf angle. All models were calculated without separating the surface into smooth and rough cutting regions.

Schlagwörter

Stichwörter der Autor:innen

abrasive water jet cuttingkerf anglemodellingsurface roughnesssurface waviness

Autor:innen und Institutionen

  • Department of Manufacturing Techniques and Automation, The Faculty of Mechanical Engineering and Aeronautics, Rzeszow University of Technology, W. Pola Str. 2, 35-959 Rzeszow, Poland.
  • Department of Manufacturing and Materials Engineering, Faculty of Mechanical Engineering, Opole University of Technology, Mikolajczyka Str. 5, 42-271 Opole, Poland.
  • Institute of Mechanical Technology, The Faculty of Mechanical Engineering, Poznan University of Technology, Piotrowo 3, 60-965 Poznan, Poland.

ORCID-Profile: Marcin Płodzień, Łukasz Żyłka, Krzysztof Żak, Szymon Wojciechowski

Zitieren

APA

Płodzień, M., Żyłka, Ł., Żak, K., & Wojciechowski, S. (2023). Modelling the Kerf Angle, Roughness and Waviness of the Surface of Inconel 718 in an Abrasive Water Jet Cutting Process. Materials, 16(15), 5288. https://doi.org/10.3390/ma16155288

Vancouver

Płodzień M, Żyłka Ł, Żak K, Wojciechowski S. Modelling the Kerf Angle, Roughness and Waviness of the Surface of Inconel 718 in an Abrasive Water Jet Cutting Process. Materials. 2023;16(15):5288. doi:10.3390/ma16155288

BibTeX
@article{Podzie2023,
  author = {Płodzień, Marcin and Żyłka, Łukasz and Żak, Krzysztof and Wojciechowski, Szymon},
  title = {Modelling the Kerf Angle, Roughness and Waviness of the Surface of Inconel 718 in an Abrasive Water Jet Cutting Process},
  journal = {Materials},
  year = {2023},
  volume = {16},
  number = {15},
  pages = {5288},
  doi = {10.3390/ma16155288}
}
Kostenlos starten →