EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Optimization of Process Parameters for Minimum Kerf Taper Angle and Surface Roughness in the Abrasive Water Jet Machining of a Hybrid Composite

Sathvik M. Bekal, Anupama Hiremath, Murthy B. R. N., Suhas K., Harisha S. R., Gurumurthy B. M., Gowri Shakar M. C.

Journal of Composites Science · 05.11.2025 · 9 (11) · 604

DOI: 10.3390/jcs9110604 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Composites Science, online erschienen am 05.11.2025. Verfasst von Sathvik M. Bekal und 6 weiteren Autor:innen. Die Arbeit wurde bisher 4-mal zitiert (Crossref) und nennt 34 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

In the present experiment, the abrasive water jet machining parameters, such as water pressure, standoff distance, and traverse speed, are selected to study the effect of each parameter on the kerf taper angle and surface roughness during the machining of glass, jute, and carbon hybrid composite. The other machining parameters are kept constant. For each parameter, three levels are fixed on the basis of previous literature reviews. The Response Surface Methodology is used to design the required number of experiments and to optimize the machining parameters to obtain the minimum kerf taper angle and surface roughness. The levels selected for water pressure are 150, 220, and 250 MPa; traverse speeds are 20, 40, and 60 mm/min; and, similarly, stand-off distances are 2, 5, and 8 mm. Experimental results confirm that the parameter inversely affects both kerf angle and surface roughness. On the other hand, parameters traverse speed and stand-off distance, directly affecting both outputs. According to RSM optimization, to obtain the minimum kerf taper angle and surface roughness, we should fix the pressure at a higher level and other parameters at a lower level. For the considered range, the obtained minimum kerf angle and roughness values are 1.4982 radians and 2.0920 μm.

Zitieren

APA

Bekal, S. M., Hiremath, A., N., M. B. R., K., S., R., H. S., M., G. B., & C., G. S. M. (2025). Optimization of Process Parameters for Minimum Kerf Taper Angle and Surface Roughness in the Abrasive Water Jet Machining of a Hybrid Composite. Journal of Composites Science, 9(11), 604. https://doi.org/10.3390/jcs9110604

Vancouver

Bekal SM, Hiremath A, N. MBR, K. S, R. HS, M. GB, et al. Optimization of Process Parameters for Minimum Kerf Taper Angle and Surface Roughness in the Abrasive Water Jet Machining of a Hybrid Composite. Journal of Composites Science. 2025;9(11):604. doi:10.3390/jcs9110604

BibTeX
@article{Bekal2025,
  author = {Bekal, Sathvik M. and Hiremath, Anupama and N., Murthy B. R. and K., Suhas and R., Harisha S. and M., Gurumurthy B. and C., Gowri Shakar M.},
  title = {Optimization of Process Parameters for Minimum Kerf Taper Angle and Surface Roughness in the Abrasive Water Jet Machining of a Hybrid Composite},
  journal = {Journal of Composites Science},
  year = {2025},
  volume = {9},
  number = {11},
  pages = {604},
  doi = {10.3390/jcs9110604}
}
Kostenlos starten →