The Influence of Osteon Orientation on Surface Topography Parameters after Machining of Cortical Bone Tissue
Materials · 09.06.2023 · 16 (12) · 4293
DOI: 10.3390/ma16124293 ↗Kurz gefasst
Fachartikel in der Zeitschrift Materials, online erschienen am 09.06.2023. Verfasst von Paweł Zawadzki und 3 weiteren Autor:innen. Beteiligte Einrichtung: Faculty of Mechanical Engineering, Poznan University of Technology, Maria Sklodowska-Curie Square 5, 60-965 Poznan, Poland. Die Arbeit wurde bisher 4-mal zitiert (Crossref) und nennt 48 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Poznań University of Technology.
Abstract (Originalsprache)
Mechanical processing of cortical bone tissue is one of the most common surgical procedures. A critical issue accompanying this processing is the condition of the surface layer, which can stimulate tissue growth and serve as a drug carrier. A comparison of the surface condition before and after orthogonal and abrasive processing was conducted to validate the influence of bone tissue’s processing mechanism and orthotropic properties on the surface topography. A cutting tool with a defined geometry and a custom-made abrasive tool was used. The bone samples were cut in three directions, depending on the orientation of the osteons. The cutting forces, acoustic emission, and surface topography were measured. The level of isotropy and the topography of the grooves showed statistical differences relative to the anisotropy directions. After orthogonal processing, the surface topography parameter Ra was determined from 1.38 ± 0.17 μm to 2.82 ± 0.32. In the case of abrasive processing, no correlation was found between the orientation of osteons and topographical properties. The average groove density for abrasive machining was below 1004 ± 0.7, and for orthogonal, it was above 1156 ± 58. Due to the positive properties of the developed bone surface, it is advisable to cut in the transverse direction and parallel to the axis of the osteons.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Faculty of Mechanical Engineering, Poznan University of Technology, Maria Sklodowska-Curie Square 5, 60-965 Poznan, Poland.
- Adult Spine Orthopaedics Department, Poznan University of Medical Sciences, 61-545 Poznan, Poland.
ORCID-Profile: Paweł Zawadzki, Karol Grochalski, Mikołaj Dąbrowski
Förderung
- Poznań University of Technology
Zitieren
APA
Zawadzki, P., Talar, R., Grochalski, K., & Dąbrowski, M. (2023). The Influence of Osteon Orientation on Surface Topography Parameters after Machining of Cortical Bone Tissue. Materials, 16(12), 4293. https://doi.org/10.3390/ma16124293
Vancouver
Zawadzki P, Talar R, Grochalski K, Dąbrowski M. The Influence of Osteon Orientation on Surface Topography Parameters after Machining of Cortical Bone Tissue. Materials. 2023;16(12):4293. doi:10.3390/ma16124293
BibTeX
@article{Zawadzki2023,
author = {Zawadzki, Paweł and Talar, Rafał and Grochalski, Karol and Dąbrowski, Mikołaj},
title = {The Influence of Osteon Orientation on Surface Topography Parameters after Machining of Cortical Bone Tissue},
journal = {Materials},
year = {2023},
volume = {16},
number = {12},
pages = {4293},
doi = {10.3390/ma16124293}
}
EUVIMED