EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

The Influence of Tool Geometry on the Mechanical Properties and the Microstructure of AA6061-T6 Aluminum Alloy Friction Stir Spot Welding

Amir Alkhafaji iD, Daniel Camas, Pablo Lopez-Crespo iD, Hayder Al-Asadi

Materials · 01.06.2023 · 16 (11) · 4135

DOI: 10.3390/ma16114135 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 01.06.2023. Verfasst von Amir Alkhafaji und 3 weiteren Autor:innen. Beteiligte Einrichtung: Department of Civil and Materials Engineering, University of Malaga, E-29071 Malaga, Spain. Die Arbeit wurde bisher 18-mal zitiert (Crossref) und nennt 30 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Programa Operativo Feder from the Junta de Andalucia (Spain).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

In this work, the influence of the tool geometry on friction stir spot welding (FSSW) was studied on sheets made of AA6061-T6 aluminum alloy. Four different AISI H13 tools with simple cylindrical and conical pin profiles and 12 mm and 16 mm shoulder diameters were used to perform the FSSW joints. Sheets of 1.8 mm thickness were used during the experimental work to prepare the lap-shear specimens. The FSSW joints were performed at room temperature. For each joining condition, four specimens were carried out. Three specimens were used to find the value of the average tensile shear failure load (TSFL), while the fourth one was used to examine the micro-Vickers hardness profile and to observe the microstructure of the cross-section of the FSSW joints. The investigation concluded that higher mechanical properties corresponding to the finer microstructure were obtained by the conical pin profile and the higher shoulder diameter compared with the specimens performed using the cylindrical pin tool and lower shoulder diameter due to the higher strain hardening and the higher frictional heat generation, respectively.

Schlagwörter

Stichwörter der Autor:innen

FSSWpin profileshoulder diameter

Autor:innen und Institutionen

  • Department of Civil and Materials Engineering, University of Malaga, E-29071 Malaga, Spain.
  • Sewerage Directorate, Nasiriyah 6400, Iraq.

ORCID-Profile: Amir Alkhafaji, Pablo Lopez-Crespo

Förderung

  • Programa Operativo Feder from the Junta de Andalucia (Spain)

Zitieren

APA

Alkhafaji, A., Camas, D., Lopez-Crespo, P., & Al-Asadi, H. (2023). The Influence of Tool Geometry on the Mechanical Properties and the Microstructure of AA6061-T6 Aluminum Alloy Friction Stir Spot Welding. Materials, 16(11), 4135. https://doi.org/10.3390/ma16114135

Vancouver

Alkhafaji A, Camas D, Lopez-Crespo P, Al-Asadi H. The Influence of Tool Geometry on the Mechanical Properties and the Microstructure of AA6061-T6 Aluminum Alloy Friction Stir Spot Welding. Materials. 2023;16(11):4135. doi:10.3390/ma16114135

BibTeX
@article{Alkhafaji2023,
  author = {Alkhafaji, Amir and Camas, Daniel and Lopez-Crespo, Pablo and Al-Asadi, Hayder},
  title = {The Influence of Tool Geometry on the Mechanical Properties and the Microstructure of AA6061-T6 Aluminum Alloy Friction Stir Spot Welding},
  journal = {Materials},
  year = {2023},
  volume = {16},
  number = {11},
  pages = {4135},
  doi = {10.3390/ma16114135}
}
Kostenlos starten →