Mechanical Performance and Microstructural Evolution of Rotary Friction Welding of Acrylonitrile Butadiene Styrene and Polycarbonate Rods
Materials · 22.04.2023 · 16 (9) · 3295
DOI: 10.3390/ma16093295 ↗Kurz gefasst
Fachartikel in der Zeitschrift Materials, online erschienen am 22.04.2023. Verfasst von Chil-Chyuan Kuo und 3 weiteren Autor:innen. Beteiligte Einrichtung: Department of Mechanical Engineering, Ming Chi University of Technology, No. 84, Gungjuan Road, New Taipei City 243, Taiwan. Die Arbeit wurde bisher 12-mal zitiert (Crossref) und nennt 45 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Ministry of Science and Technology of Taiwan, the Ministry of Science and Technology of Taiwan.
Abstract (Originalsprache)
Rotary friction welding (RFW) is a green manufacturing technology with environmental pollution in the field of joining methods. In practice, the welding quality of the friction-welded parts was affected by the peak temperature in the weld joint during the RFW of dissimilar plastic rods. In industry, polycarbonate (PC) and acrylonitrile butadiene styrene (ABS) are two commonly used plastics in consumer products. In this study, the COMSOL multiphysics software was employed to estimate the peak temperature in the weld joint during the RFW of PC and ABS rods. After RFW, the mechanical performance and microstructural evolution of friction-welded parts were investigated experimentally. The average Shore A surface hardness, flexural strength, and impact energy are directly proportional to the rotation speed of the RFW. The quality of RFW is excellent, since the welding strength in the weld joint is better than that of the ABS base materials. The fracture occurs in the ABS rods since their brittleness is higher than that of the PC rods. The average percentage error of predicting the peak temperature using COMSOL software using a mesh element count of 875,688 for five different rotation speeds is about 16.6%. The differential scanning calorimetry curve for the friction-welded parts welded at a rotation speed of 1350 rpm shows an endothermic peak between 400 to 440 °C and an exothermic peak between 600 to 700 °C, showing that the friction-welded parts have better mechanical properties.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Department of Mechanical Engineering, Ming Chi University of Technology, No. 84, Gungjuan Road, New Taipei City 243, Taiwan.
- Research Center for Intelligent Medical Devices, Ming Chi University of Technology, No. 84, Gungjuan Road, New Taipei City 243, Taiwan.
- Department of Mechanical Engineering, Chang Gung University, No.259, Wenhua 1st Rd., Guishan Dist., Taoyuan City 333, Taiwan.
- Department of Mechanical Engineering, Presidency University, Rajankunte, Near Yelhanka, Bangalore 700073, India.
- Li-Yin Technology Co., Ltd., No. 37, Lane 151, Section 1, Zhongxing Road, Wugu District, New Taipei City 241, Taiwan.
ORCID-Profile: Chil-Chyuan Kuo
Förderung
- Ministry of Science and Technology of Taiwan
- the Ministry of Science and Technology of Taiwan
Zitieren
APA
Kuo, C. C., Gurumurthy, N., Chen, H. W., & Hunag, S. H. (2023). Mechanical Performance and Microstructural Evolution of Rotary Friction Welding of Acrylonitrile Butadiene Styrene and Polycarbonate Rods. Materials, 16(9), 3295. https://doi.org/10.3390/ma16093295
Vancouver
Kuo CC, Gurumurthy N, Chen HW, Hunag SH. Mechanical Performance and Microstructural Evolution of Rotary Friction Welding of Acrylonitrile Butadiene Styrene and Polycarbonate Rods. Materials. 2023;16(9):3295. doi:10.3390/ma16093295
BibTeX
@article{Kuo2023,
author = {Kuo, Chil-Chyuan and Gurumurthy, Naruboyana and Chen, Hong-Wei and Hunag, Song-Hua},
title = {Mechanical Performance and Microstructural Evolution of Rotary Friction Welding of Acrylonitrile Butadiene Styrene and Polycarbonate Rods},
journal = {Materials},
year = {2023},
volume = {16},
number = {9},
pages = {3295},
doi = {10.3390/ma16093295}
}
EUVIMED