EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Scratch and Wear Behaviour of Co-Cr-Mo Alloy in Ringer’s Lactate Solution

Raimundo Silva iD, Marcos Dantas Dos Santos iD, Rui Madureira iD, Rui Soares, Rui Neto, Ângela Aparecida Vieira, Polyana Alves Radi Gonçalves iD, Priscila Maria Sarmeiro M Leite, Lúcia Vieira iD, Filomena Viana iD

Materials · 06.04.2023 · 16 (7) · 2923

DOI: 10.3390/ma16072923 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 06.04.2023. Verfasst von Raimundo Silva und 9 weiteren Autor:innen. Beteiligte Einrichtung: Department of Materials Engineering, University of the State of Amazonas (UEA), Darcy Vargas, Manaus 69050-020, Brazil. Die Arbeit wurde bisher 20-mal zitiert (Crossref) und nennt 78 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: GRIS project, COMPETE 2020, through FEDER and FCT, projects MAGIC 4.0.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Cobalt–chromium–molybdenum (Co-Cr-Mo) alloy is a material recommended for biomedical implants; however, to be suitable for this application, it should have good tribological properties, which are related to grain size. This paper investigates the tribological behaviour of a Co-Cr-Mo alloy produced using investment casting, together with electromagnetic stirring, to reduce its grain size. The samples were subjected to wear and scratch tests in simulated body fluid (Ringer’s lactate solution). Since a reduction in grain size can influence the behaviour of the material, in terms of resistance and tribological response, four samples with different grain sizes were produced for use in our investigation of the behaviour of the alloy, in which we considered the friction coefficient, wear, and scratch resistance. The experiments were performed using a tribometer, with mean values for the friction coefficient, normal load, and tangential force acquired and recorded by the software. Spheres of Ti-6Al-4V and 316L steel were used as counterface materials. In addition, to elucidate the influence of grain size on the mechanical properties of the alloy, observations were conducted via scanning electron microscopy (SEM) with electron backscatter diffraction (EBSD). The results showed changes in the structure, with a reduction in grain size from 5.51 to 0.79 mm. Using both spheres, the best results for the friction coefficient and wear volume corresponded to the sample with the smallest grain size of 0.79 mm. The friction coefficients obtained were 0.37 and 0.45, using the Ti-6Al-4V and 316L spheres, respectively. These results confirm that the best surface finish for Co-Cr-Mo alloy used as a biomedical implant is one with a smaller grain size, since this results in a lower friction coefficient and low wear.

Schlagwörter

Stichwörter der Autor:innen

cobalt–chromium–molybdenum alloyhip replacementsorthopaedicsscratch testwear

Autor:innen und Institutionen

  • Department of Materials Engineering, University of the State of Amazonas (UEA), Darcy Vargas, Manaus 69050-020, Brazil.
  • Department of Metallurgical and Materials Engineering, Faculty of Engineering, University of Porto, Rua Dr. Roberto Frias, 4200-465 Porto, Portugal.
  • LAETA/INEGI-Institute of Science and Innovation in Mechanical and Industrial Engineering, Rua Dr. Roberto Frias, 4200-465 Porto, Portugal.
  • Department of Mechanical Engineering, Faculty of Engineering, University of Porto, Rua Dr. Roberto Frias, 4200-465 Porto, Portugal.
  • Department of Materials, Institute of Research and Development (IP&D), University of Paraíba Valley, São José dos Campos 12244-000, Brazil.

ORCID-Profile: Raimundo Silva, Marcos Dantas Dos Santos, Rui Madureira, Polyana Alves Radi Gonçalves, Lúcia Vieira, Filomena Viana

Förderung

  • GRIS project
  • COMPETE 2020, through FEDER and FCT
  • projects MAGIC 4.0
  • HIPERCAST

Zitieren

APA

Silva, R., Santos, M. D. D., Madureira, R., Soares, R., Neto, R., Vieira, Â. A., Gonçalves, P. A. R., Leite, P. M. S. M., Vieira, L., & Viana, F. (2023). Scratch and Wear Behaviour of Co-Cr-Mo Alloy in Ringer’s Lactate Solution. Materials, 16(7), 2923. https://doi.org/10.3390/ma16072923

Vancouver

Silva R, Santos MDD, Madureira R, Soares R, Neto R, Vieira ÂA, et al. Scratch and Wear Behaviour of Co-Cr-Mo Alloy in Ringer’s Lactate Solution. Materials. 2023;16(7):2923. doi:10.3390/ma16072923

BibTeX
@article{Silva2023,
  author = {Silva, Raimundo and Santos, Marcos Dantas Dos and Madureira, Rui and Soares, Rui and Neto, Rui and Vieira, Ângela Aparecida and Gonçalves, Polyana Alves Radi and Leite, Priscila Maria Sarmeiro M and Vieira, Lúcia and Viana, Filomena},
  title = {Scratch and Wear Behaviour of Co-Cr-Mo Alloy in Ringer’s Lactate Solution},
  journal = {Materials},
  year = {2023},
  volume = {16},
  number = {7},
  pages = {2923},
  doi = {10.3390/ma16072923}
}
Kostenlos starten →