EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Investigation of the Hot Stamping-in-Die Quenching Composite Forming Process of 5083 Aluminum Alloy Skin

Lingling Yi, Ge Yu, Ziming Tang, Xin Li, Zhengwei Gu

Materials · 29.03.2023 · 16 (7) · 2742

DOI: 10.3390/ma16072742 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 29.03.2023. Verfasst von Lingling Yi und 4 weiteren Autor:innen. Beteiligte Einrichtung: Department of Materials Science and Engineering, Jilin University, Changchun 130022, China. Die Arbeit wurde bisher 11-mal zitiert (Crossref) und nennt 49 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: National Natural Science Foundation of China, Technology Development Program of Jilin Province.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Aluminum alloy has been used as the skin material for rail vehicles and automobiles to meet the requirements of environmental protection. The hot stamping-in-die quenching composite forming (HFQ) process is a promising technology to compensate for the poor formability of the aluminum alloy sheet at room temperature. In this paper, the high-temperature mechanical properties of 5083 aluminum alloy under various temperature (200 °C, 300 °C, 400 °C, 450 °C) and strain rate conditions (0.01 s−1, 0.10 s−1, 1.00 s−1) were investigated by uniaxial tensile tests. The finite element software of PAM-STAMP was employed to simulate the forming process of high-speed train skin. The effects of forming method and process parameters on the minimum thickness and springback of the skin were analyzed using the Response Surface Methodology (RSM). After parameter optimization, the forming experiment verified the simulation results and the test part met the quality requirements: the thickness above 3.84 mm and the springback within 1.1 mm. Mechanical properties of the sheet before and after HFQ were examined by uniaxial tensile tests at room temperature. It can be inferred from the comparison that the yield strength of the Al5083 sheet increases, but the elongation decreases from the HFQ process.

Schlagwörter

Stichwörter der Autor:innen

Al5083finite element methodhigh-speed train skinhot stamping

Autor:innen und Institutionen

  • Department of Materials Science and Engineering, Jilin University, Changchun 130022, China.
  • State Key Laboratory of Automobile Materials, Jilin University, Changchun 130022, China.
  • Roll Forging Research Institute, Jilin University, Changchun 130022, China.

Förderung

  • National Natural Science Foundation of China
  • Technology Development Program of Jilin Province

Zitieren

APA

Yi, L., Yu, G., Tang, Z., Li, X., & Gu, Z. (2023). Investigation of the Hot Stamping-in-Die Quenching Composite Forming Process of 5083 Aluminum Alloy Skin. Materials, 16(7), 2742. https://doi.org/10.3390/ma16072742

Vancouver

Yi L, Yu G, Tang Z, Li X, Gu Z. Investigation of the Hot Stamping-in-Die Quenching Composite Forming Process of 5083 Aluminum Alloy Skin. Materials. 2023;16(7):2742. doi:10.3390/ma16072742

BibTeX
@article{Yi2023,
  author = {Yi, Lingling and Yu, Ge and Tang, Ziming and Li, Xin and Gu, Zhengwei},
  title = {Investigation of the Hot Stamping-in-Die Quenching Composite Forming Process of 5083 Aluminum Alloy Skin},
  journal = {Materials},
  year = {2023},
  volume = {16},
  number = {7},
  pages = {2742},
  doi = {10.3390/ma16072742}
}
Kostenlos starten →